Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Toshiba e-Studio 207L — Trang 25/33

Code: ED12

Description: Shutter home position error: The shutter is not at the home position. [MJ-1101/MJ-1106]
Causes: MJ-1101 Shutter clutch Shutter opening/closing sensor Finisher controller PC board
MJ-1106 Movable tray paper-full sensor Finisher controller PC board Shutter opening/closing sensor
Remedy: MJ-1101 Shutter Open and close the shutter. If there is any mechanical problem, fix its mechanism. Shutter opening/closing sensor Shutter clutch Finisher controller PC board Check if the connectors on the finisher controller PC board are disconnected from the shutter opening/closing sensor (S4) and the shutter clutch (CLT1), or the harnesses are open circuited. Correct if any.
MJ-1106 Movable tray paper-full sensor Fix any mechanical problem occurring when the actuator is moved. Check if there is a disconnection of the connector, incorrect installation or breakage of the movable tray paper-full sensor (S16). If there is, reinstall the sensor correctly or replace it. Check if the connector (CN12) on the finisher controller PC board is disconnected from the movable tray paper-full sensor (S16) and the harnesses are open circuited. Correct if so. Shutter Open and close the shutter. Fix any mechanical problem. Shutter opening/closing sensor Check if there is a disconnection of the connector, incorrect installation or breakage of the shutter opening/closing sensor (S4). If there is, reinstall the sensor correctly or replace it. Check if the connector (CN12) on the finisher controller PC board is disconnected from the shutter opening/closing sensor (S4) and the harnesses are open circuited. Correct if so. Shutter clutch Check if the connector (CN10) on the finisher controller PC board is disconnected from the shutter clutch (CLT1) and the harnesses are open circuited. Correct if so.

Code: ED13

Description: Front alignment plate home position error: The front alignment plate is not at the home position. [MJ- 1101/MJ-1106]
Causes: MJ-1101 Front alignment motor Front alignment plate home position sensor Finisher controller PC board
MJ-1106 Front alignment plate home position sensor Finisher controller PC board
Remedy: MJ-1101 Front alignment plate Move the front alignment plate. If there is any mechanical problem, fix its mechanism. Front alignment motor Front alignment plate home position sensor Finisher controller PC board Check if the connectors on the finisher controller PC board are disconnected from the front alignment plate home position sensor (S7) and the front alignment motor (M9), or the harnesses are open circuited. Correct if any.
MJ-1106 Front alignment plate Move the front alignment plate. Fix any mechanical problem. Front alignment plate home position sensor Check if there is a disconnection of the connector, incorrect installation or breakage of the front alignment plate home position sensor (S7). If there is, reinstall the sensor correctly or replace it. Check if the connector (CN18) on the finisher controller PC board is disconnected from the front alignment plate home position sensor (S7) and the harnesses are open circuited. Correct if so. Front alignment motor Check if the connector (CN17) on the finisher controller PC board is disconnected from the front alignment motor (M5) and the harnesses are open circuited. Correct if so.

Code: ED14

Description: Rear alignment plate home position error: The rear alignment plate is not at the home position. [MJ- 1101/MJ-1106]
Causes: MJ-1101 Front alignment motor Front alignment plate home position sensor Finisher controller PC board
MJ-1106 Rear alignment plate home position sensor Finisher controller PC board
Remedy: MJ-1101 Rear alignment plate Move the Rear alignment plate. If there is any mechanical problem, fix its mechanism. Rear alignment motor Rear alignment plate home position sensor Finisher controller PC board Check if the connectors on the finisher controller PC board are disconnected from the Rear alignment plate home position sensor (S8) and the Rear alignment motor (M10), or the harnesses are open circuited. Correct if any.
MJ-1106 Rear alignment plate Move the rear alignment plate. Fix any mechanical problem. Rear alignment plate home position sensor Check if there is a disconnection of the connector, incorrect installation or breakage of the rear alignment plate home position sensor (S8). If there is, reinstall the sensor correctly or replace it. Check if the connector (CN18) on the finisher controller PC board is disconnected from the rear alignment plate home position sensor (S8) and the harnesses are open circuited. Correct if so. Rear alignment motor Check if the connector (CN17) on the finisher controller PC board is disconnected from the rear alignment motor (M6) and the harnesses are open circuited. Correct if so.

Code: ED15

Description: Paddle home position error: The paddle is not at the home position. [MJ-1101/MJ-1106]
Causes: MJ-1101 Paddle motor Paddle home position sensor Finisher controller PC board
MJ-1106 Rear alignment motor Finisher controller PC board
Remedy: MJ-1101 Paddle Rotate the paddle. If there is any mechanical problem, fix its mechanism. Paddle home position sensor Paddle motor Finisher controller PC board Check if the connectors on the finisher controller PC board are disconnected from the paddle home position sensor (S3) and the paddle motor (M8), or the harnesses are open circuited. Correct if any.
MJ-1106 Rear alignment plate Move the rear alignment plate. Fix any mechanical problem. Rear alignment motor Check if the connector (CN17) on the finisher controller PC board is disconnected from the rear alignment motor (M6) and the harnesses are open circuited. Correct if so.
MJ-1033 Transport motor-2 Paddle home position sensor The paddle home position sensor (S34) does not change from "ON" to "OFF" within the pre-specified time during paddle rotation. The paddle home position sensor (S34) does not change from "OFF" to "ON" within the pre-specified time during paddle rotation.

Code: ED16

Description: Buffer tray home position error: The buffer tray is not at the home position. [MJ-1101/MJ-1106]
Causes: MJ-1101 Buffer tray guide motor Buffer tray home position sensor Finisher controller PC board
MJ-1106 Buffer tray home position sensor Finisher controller PC board
Remedy: MJ-1101 Buffer tray guide Open and close the buffer tray guide. If there is any mechanical problem, fix its mechanism. Buffer tray home position sensor Buffer tray guide motor Finisher controller PC board Check if the connectors on the finisher controller PC board are disconnected from the buffer tray home position sensor (S5) and the buffer tray guide motor (M3), or the harnesses are open circuited. Correct if any.
MJ-1106 Buffer tray guide Open and close the buffer tray guide. Fix any mechanical problem. Buffer tray home position sensor Check if there is a disconnection of the connector, incorrect installation or breakage of the buffer tray home position sensor (S5). If there is, reinstall the sensor correctly or replace it. Check if the connector (CN11) on the finisher controller PC board is disconnected from the buffer tray home position sensor (S5) and the harnesses are open circuited. Correct if so. Assist arm motor Check if the connector (CN13) on the finisher controller PC board is disconnected from the assist arm motor (M10) and the harnesses are open circuited. Correct if so.

Code: EF10

Description: Paper not supported for Saddle Stitch Finisher: Unsupported paper size, type and an excess number of pages for stapling are selected. [MJ- 1106]
Causes: Buffer tray home position sensor Buffer tray guide motor Saddle controller board
Remedy: Paper • Paper size check Buffer tray home position sensor • Sensor check • Connector check • Harness check Buffer tray guide motor • Motor check • Connector check • Harness check Saddle controller board • Connector check • Board check

Code: EF11

Description: Saddle Stitch Finisher stapling error (front): Front stapling is not correctly done. [MJ-1106]
Causes: Front saddle stapler drive unit Saddle controller board
Remedy: Finisher • Is there any paper remaining on the paper transport path in the Finisher or the equipment, or on the finishing tray?. Saddle staple cartridge (Front side) • Is the jam released by taking off the front staple cartridge from the Finisher and removing the staple sheet slid from the staple case? Front saddle stapler drive unit • Unit check • Connector check • Harness check Saddle controller board • Connector check (CN3) • Board check

Code: EF12

Description: Saddle Stitch Finisher stapling error (rear): Rear stapling is not correctly done. [MJ-1106]
Causes: Rear saddle stapler drive unit Saddle controller board
Remedy: Finisher • Is there any paper remaining on the paper transport path in the Finisher or the equipment, or on the finishing tray?. Saddle staple cartridge (rear side) • Is the jam released by taking off the rear staple cartridge from the Finisher and removing the staple sheet slid from the staple case? Rear saddle stapler drive unit • Unit check • Connector check • Harness check Saddle controller board • Connector check (CN3) • Board check
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie