Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Toshiba e-Studio 210c — Trang 5/17

Code: C5A

Description: Communications error between LGC-CPU and printer controller
Remedy: <<For a built-in type printer controller>> 1. Check if the printer controller unit is securely mounted on the copier. 2. Check if the harness between the LGC and IMC boards is open-circuited, and if the connector J113 on the LGC board and the connector J182 on the IMC board are disconnected. 3. Check if the harness between the switching power supply and the printer controller is open-circuited. 4. Check if the connector J710 of the switching power supply is disconnected. 5. Check if any conductor pattern on the IMC, IMG, MTH2 and LGC boards is open- or shortcircuited . 6. Replace the LGC board. 7. Replace the IMG board. 8. Replace the IMC board. 9. Replace the MTH2 board. <<For an external type printer controller>> 1. Check if the printer controller power is turned ON. 2. Check if the harness between the PIF board and the printer controller is open-circuited. 3. Check if the PIF board is firmly connected to the MTH2 board. 4. Check if the harness between the LGC and IMC boards is open-circuited, and if the connector J113 on the LGC board and the connector J182 on the IMC board are disconnected. 5. Check if any conductor pattern on the PIF, IMG, MTH2, IMC and LGC boards is open- or short-circuited. 6. Replace the PIF board. 7. Replace the LGC board. 8. Replace the IMG board. 9. Replace the IMC board. 10. Replace the MTH2 board.

Code: C5B

Description: LGC-CPU signal transmission error to IMC-CPU
Remedy: 1. Check if the harness between the LGC and IMC boards is open-circuited, and if the connector J113 on the LGC board and the connector J182 on the IMC board are disconnected. 2. Replace the LGC board. 3. Replace the IMC board.

Code: C5C

Description: LGC-CPU signal reception error from IMC-CPU
Remedy: 1. Check if the harness between the LGC and IMC boards is open-circuited, and if the connector J113 on the LGC board and the connector J182 on the IMC board are disconnected. 2. Replace the LGC board. 3. Replace the IMC board.

Code: C7

Description: Error C7
Remedy: 1. Check if any thermistor connector is disconnected. 2. Check if any harness of the thermistors (center/rear, upper/lower) is open-circuited. 3. Check the LGC board if the connector J122 is disconnected. 4. After completing the repair of what caused the [C7] problem, proceed to rewrite the status counter (08-700) to "0", following the same procedure as for [C41] to [C48] .

Code: C72

Description: Aligning sensor automatic adjustment error
Remedy: 1. Check if any foreign matter is present between the aligning sensor and the reflecting mirror, and if the reflecting mirror is stained. 2. Check if the harness between the aligning sensor and the RADF PC board is open-circuited. 3. Check if any conductor pattern on the RADF PC board is open- or short-circuited mainly around IC1, IC14 and CN14. 4. Replace the aligning sensor. 5. Replace the RADF PC board. 6. Initialize the RADF's EEPROM and perform the sensor automatic adjustment.

Code: C73

Description: EEPROM initializing error
Remedy: 1. Check if any conductor pattern on the RADF PC board is open- or short-circuited mainly around IC7. 2. Replace the RADF PC board. 3. Initialize the RADF's EEPROM and perform the sensor automatic adjustment.

Code: C74

Description: Paper exit sensor automatic adjustment error
Remedy: 1. Check if any foreign matter is present between the exit sensor and the reflecting mirror, and if the reflecting mirror is stained. 2. Check if the harness between the exit sensor and the RADF PC board is open-circuited. 3. Check if any conductor pattern on the RADF PC board is open- or short-circuited mainly around IC1, IC14 and CN8. 4. Replace the exit sensor. 5. Replace the RADF PC board. 6. Initialize the RADF's EEPROM and perform the sensor automatic adjustment.

Code: C82

Description: Communications error between scanner and ADF
Remedy: 1. Check if the connectors are disconnected or the harnesses are open-circuited between the SCM board and RADF PC board (includig the relay connector). 2. Replace the RADF PC board. 3. Replace the SCM board.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie