Description: [MJ-1110] Stacker jam in the saddle stitch unit
Causes: Stacker paper detection sensor (S30) Saddle control PC board (SDL)
Remedy: Paper • Is there any paper remaining in the paper transport path in the equipment or the saddle stitch section of the Finisher? Stacker paper detection sensor (S30) • Sensor check • Connector check (CN3) • Harness check Saddle control PC board (SDL) • Connector check (CN3) • Board check
Description: Communication error between System-CPU and Engine-CPU
Causes: LGC board SYS board Harness
Remedy: Error code • Turn the power OFF and then back ON using the main power switch, and then check if the error code changes to another one. • If it changes to another one, follow the procedure for the changed error code. Check firmware version • Check the version of the system firmware on the SYS board. • Check the version of the engine firmware on the LGC board. Board check • Check if the connector (CN131, CN132) on the SYS board and the connector (CN330, CN329) on the LGC board are completely inserted. • Check if the connector pin between the SYS board connectors (CN131, CN132) and the LGC board connectors (CN330, CN329) is disconnected. • Check if the connector CN314 on the LGC board and the connector CN512 on the PS-ACC are completely inserted. • Check if the conductor patterns on the LGC board and SYS board are short circuited or open circuited Harness • Connector check • Harness check
Description: Communication initialization error between System-CPU and Engine-CPU
Causes: LGC board SYS board Harness
Remedy: Error code • Turn the power OFF and then back ON using the main power switch, and then check if the error code changes to another one. • If it changes to another one, follow the procedure for the changed error code. Check firmware version • Check the version of the system firmware on the SYS board. • Check the version of the engine firmware on the LGC board. Board check • Check if the connector (CN131, CN132) on the SYS board and the connector (CN330, CN329) on the LGC board are completely inserted. • Check if the connector pin between the SYS board connectors (CN131, CN132) and the LGC board connectors (CN330, CN329) is disconnected. • Check if the connector CN314 on the LGC board and the connector CN512 on the PS-ACC are completely inserted. • Check if the conductor patterns on the LGC board and SYS board are short circuited or open circuited Harness • Connector check • Harness check LGC board • 25/30/35 ppm: Measure the voltage on TP33 on the LGC board. Then check that the measured voltage is 3.3V. If the voltage does not output, replace the LGC board. • 45/50 ppm: Measure the voltage on TP18 on the LGC board. Then check that the measured voltage is 3.3V. If the voltage does not output, replace the LGC board.
Remedy: SRAM 1. Check that the SRAM is installed properly. 2. Shut down the equipment. 3. Perform [FS-08]. 4. Press [CLASSIC]. 5. When “SRAM REQUIRES INITIALIZATION” appears on the LCD screen, confirm the destination and press the [START] button. If the destination is incorrect, enter the number for the correct one and press the [START] button. 6. When the confirmation message appears on the LCD screen, press [INITIALIZE]. (SRAM initialization starts.) 7. Enter the serial number of the equipment correctly. (FS-08- 9601) 8. Initialize the NIC information. (FS-08-9083) 9. Shut down the equipment. 10.Perform [FS-05]. 11.Press [CLASSIC]. 12.Perform “Data transfer of characteristic value of scanner”. (FS-05-3203, FS-05-3240) 13.By using the [4] [TEST PRINT] test pattern, perform “Automatic gamma adjustment” <PPC>. (FS-05-7869) 14.By using the [70] [TEST PRINT] test pattern, perform “Automatic gamma adjustment” <PRT>. (FS-05-8008) 15.Reboot the equipment. 16.If the error still occurs, replace the SRAM. SYS board Board check
Remedy: SYS board Board check Combination of the firmware version • Check the combination of the firmware version of the system firmware, system software, engine firmware, and scanner firmware. • Reinstall the firmware of correct combination.
Nhận ưu đãi sớm nhất khi chương trình diễn ra
Đăng ký nhận bản tin
Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này.
Chính sách cookie
Những cookie này là cần thiết để trang web hoạt động đúng cách.
Những cookie này giúp chúng tôi hiểu cách khách truy cập tương tác với trang web.
Những cookie này được sử dụng để cung cấp quảng cáo cá nhân hóa.