Description: LCF transport jam (Paper not reaching the 2nd transport sensor): The paper does not reach the 2nd transport sensor after it has passed the LCF feed sensor.
Causes: 2nd transport sensor. LGC board PFP transport clutch PFP board Feed roller Separation roller Pickup roller
Remedy: 1 Open the side cover. Is there paper in front of the 2nd transport sensor? Yes Remove the paper. No 2 2 Is the 2nd transport sensor working? (Perform the input check in the test mode: FS-03- [F3]ON/[4]/[D]) Yes 3 No • Check if the connector of the 2nd transport sensor is disconnected. • Check if the connector CN318 on the LGC board is disconnected. • Check if the connector pins are disconnected and the harnesses are open circuited. • Check if the conductor pattern on the LGC board is short circuited or open circuited. • Replace the 2nd transport sensor. • Replace the LGC board. 3 Is the PFP transport clutch working? (Perform the output check in the test mode: 03-225) Yes 4 No • Check if the connector of the PFP transport clutch is disconnected. • Check if any of the connectors CN241 and CN247 on the PFP board is disconnected. • Check if the connector CN315 on the LGC board is disconnected. • Check if the connector pins are disconnected and the harnesses are open circuited. • Check if the conductor patterns on the PFP board and LGC board are short circuited or open circuited. • Replace the PFP transport clutch. • Replace the PFP board. • Replace the LGC board. 4 Feed roller Separation roller] Pickup roller Transfer roller • Check the condition of the feed roller, separation roller and pickup roller of each paper source, and replace them if they are worn out. • Check the transport roller. Replace it if it is worn out.
Description: Front cover open jam: The front cover has opened during printing.
Causes: Front cover switch LGC board
Remedy: 1 Is the front cover open? Yes Close the cover. No 2 2 Is the front cover switch working? (Perform the input check in the test mode: FS-03- [ALL]OFF/[7]/[C]) Yes 3 No • Check if the connector of the front cover switch is disconnected. • Check if the connector CN319 on the LGC board is disconnected. • Check if the connector pins are disconnected and the harnesses are open circuited. • Check if the conductor pattern on the LGC board is short circuited or open circuited. • Replace the front cover switch. • Replace the LGC board. 3 Is the voltage of 24V being supplied from the power supply unit? (Perform the input check in the test mode: FS-03- [ALL]OFF/[7]/[D]) Yes 4 No • Check if the connector for 24 V power supply is disconnected. • Check if the connector CN301 on the LGC board is disconnected. • Check if the connector pins are disconnected and the harnesses are open circuited. • Check if the conductor pattern on the LGC board is short circuited or open circuited. • Replace the LGC board. 4 LGC board • Replace the LGC board.
Description: PFP side cover open jam: The PFP side cover has opened during printing
Causes: PFP side cover opening/closing switch PFP board LGC board
Remedy: 1 Is the PFP side cover open? Yes Remove the paper if there is any, then close the cover. No 2 2 Is the PFP side cover opening/closing switch working? (Perform the input check in the test mode: FS-03- [F3]ON/[0]/[A]) Yes 3 No • Check if the connector of the PFP side cover opening/closing switch is disconnected. • Check if either of the connectors CN241 or CN247 on the PFP board is disconnected. • Check if the connector CN315 on the LGC board is disconnected. • Check if the connector pins are disconnected and the harnesses are open circuited. • Check if the conductor patterns on the PFP board and LGC board are short circuited or open circuited. • Replace the PFP side cover opening/ closing switch. • Replace the PFP board. • Replace the LGC board. 3 Replacing board • Replace the PFP board. • Replace the LGC board.
Description: ADU open jam: The ADU has opened during printing.
Causes: ADU opening/closing switch LGC board
Remedy: 1 Is the ADU open? Yes Remove the paper if there is any, then close the ADU. No 2 2 Is the ADU opening/ closing switch working? (Perform the input check in the test mode: FS-03- [ALL]OFF/[7]/[A]) Yes 3 No • Check if the connector of the ADU opening/ closing switch is disconnected. • Check if the connector CN311 on the LGC board is disconnected. • Check if the connector pins are disconnected and the harnesses are open circuited. • Check if the conductor patterns on the LGC board are short circuited or open circuited. • Replace the ADU opening/closing switch. • Replace the LGC board. 3 Replacing board • Replace the LGC board.
Remedy: 1 Is the feed cover open? Yes Remove the paper if there is any, then close the cover. No 2 2 Is the feed cover opening/ closing switch working? (Perform the input check in the test mode: FS-03- [F3]ON/[4]/[A]) Yes 3 No • Check if the connector of the feed cover opening/closing switch is disconnected. • Check if the connector CN318 on the LGC board is disconnected. • Check if the connector pins are disconnected and the harnesses are open circuited. • Check if the conductor pattern on the LGC board is short circuited or open circuited. • Replace the feed cover opening/closing switch. • Replace the LGC board. 3 Replacing board • Replace the LGC board.
Remedy: 1 Is the LCF jam access cover open? Yes Remove the paper if there is any, then close the cover. No 2 2 Is the LCF jam access cover opening/closing switch working? (Perform the input check in the test mode: FS-03- [F1]ON/[9]/[A]) Yes 3 No • Check if the connector of the LCF jam access cover opening/closing switch is disconnected. • Check if either of the connectors CN1 or CN7 on the LCF board is disconnected. • Check if the connector CN315 on the LGC board is disconnected. • Check if the connector pins are disconnected and the harnesses are open circuited. • Check if the conductor patterns on the LCF board and LGC board are short circuited or open circuited. • Replace the LCF jam access cover opening/closing switch. • Replace the LCF board. • Replace the LGC board. 3 Replacing board • Replace the LCF board. • Replace the LGC board.
Description: Bridge unit open jam: The bridge unit has opened during printing.
Causes: The bridge unit opening/closing switch LGC board
Remedy: 1 Is the bridge unit open? Yes Remove the paper if there is any, then close the unit. No 2 2 Is the bridge unit opening/ closing switch working? (Perform the input check in the test mode: FS-03-[ALL]OFF/[7]/[B]) Yes 3 No • Check if the connector of the bridge unit opening/closing switch is disconnected. • Check if the connector CN311 on the LGC board is disconnected. • Check if the connector pins are disconnected and the harnesses are open circuited. • Check if the conductor pattern on the LGC board is short circuited or open circuited. • Replace the bridge unit opening/closing switch. • Replace the LGC board. 3 Replacing board • Replace the LGC board.
Description: Job separator cover open jam: The job separator cover has opened during printing.
Causes: JSP cover switch JSP board LGC board
Remedy: 1 Is the JSP cover open? Yes Remove the paper if there is any, then close the cover. No 2 2 Is the JSP cover switch working? (Perform the input check in the test mode: FS-03- [ALL]OFF/[7]/[B]) Yes 3 No • Check if the connector of the JSP cover switch is disconnected. • Check if either of the connectors CN260 or CN261 on the JSP board is disconnected. • Check if the connector CN311 on the LGC board is disconnected. • Check if the connector pins are disconnected and the harnesses are open circuited. • Check if the conductor patterns on the JSP board and LGC board are short circuited or open circuited. • Replace the JSP cover switch. • Replace the JSP board. • Replace the LGC board. 3 Replacing board • Replace the JSP board. • Replace the LGC board.
Nhận ưu đãi sớm nhất khi chương trình diễn ra
Đăng ký nhận bản tin
Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này.
Chính sách cookie
Những cookie này là cần thiết để trang web hoạt động đúng cách.
Những cookie này giúp chúng tôi hiểu cách khách truy cập tương tác với trang web.
Những cookie này được sử dụng để cung cấp quảng cáo cá nhân hóa.