Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Toshiba e-Studio 2555CSE — Trang 6/36

Code: C4E1

Description: Fuser pressure roller contact/semi-contact abnormality - Though the pressure roller is contacted, its position cannot be detected.
Causes: Pressure roller contact/release detection sensor Pressure roller contact/release motor LGC board
Remedy: Pressure roller contact/release detection sensor (S27, S28) • Sensor check (Perform the input check: 03-[FAX]ON/[2]/[G], 03- [FAX]ON/[2]/[H]) • Connector check (J1116, J1117) • Harness check Pressure roller contact/release motor (M13) • Motor check (Perform the output check: 03-272) • Connector check (CN353) • Harness check Fuser unit • Drawer connector check • Thermostat check • Unit check LGC board • Connector check (CN355, CN356) • Board check

Code: C4E2

Description: Fuser belt rotation detection sensor abnormality - The fuser belt does not rotate or incorrectly rotates.
Causes: Fuser belt rotation detection sensor Detection plate (rotor) Dirty/damaged Fuser belt Deformed/damaged Bushing of fuser belt drive shaft Worn Bushing of fuser drive unit Worn Drive plate Bend section broken Gear Teeth damaged, worn LGC board
Remedy: Fuser unit • Fuser belt rotation detection sensor check (Input check: 03-[ALL]OFF/[6]/[A]) • Connector check in the fuser belt rotation sensor • Harness check in the fuser belt rotation sensor • Rotation detection plate (rotor) check • Grease check in the gear (shaft / tooth flank) • Fuser belt check • Check if the bushing of fuser belt drive shaft is worn. • Fuser unit installation check (Check that the levers fixing the fuser unit are lifted up.) Fuser drive unit • Bushing check • Check that the drive unit is correctly installed (3 dowels). • Check that the drive metal plate is not broken. • Check that the gear is not damaged or worn. • One-way clutch check • Grease check in the gear (shaft / tooth flank) LGC board • Connector check (CN355, CN356) • Board check

Code: C550

Description: RADF I/F error: Communication error has occurred between the RADF and the scanner.
Causes: RADF board SYS board
Remedy: RADF board • Check if the harness connecting the RADF board and SYS board is disconnected or open circuited. • Check if the conductor pattern on the RADF board is short circuited or open circuited. • Connector check SYS board • Check if the conductor pattern on the SYS board is short circuited or open circuited. • Connector check

Code: C551

Description: RADF model detection error
Causes: RADF
Remedy: RADF • Replace the RADF with the correct one.

Code: C560

Description: Communication error between Engine-CPUs
Causes: LGC board
Remedy: LGC board Turn the power OFF and then back ON using the main power switch. If the same error occurs again, replace the LGC board.

Code: C580

Description: Communication error between LGC board and finisher
Causes:
Remedy: Finisher Check if the specified finisher is attached.

Code: C5A0

Description: EEPROM not connected (LGC board)
Causes: EEPROM LGC board
Remedy: EEPROM EEPROM check LGC board • IC socket check (IC52) • Board check

Code: C5A1

Description: EEPROM data abnormality (LGC board)
Causes: EEPROM LGC board
Remedy: EEPROM EEPROM check LGC board • IC socket check (IC52) • Board check
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie