Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Toshiba e-Studio 2820c — Trang 16/33

Code: E063

Description: Incorrect paper size setting for PFP upper drawer: The size of paper in the 3rd drawer differs from size setting of the equipment.
Causes: SYS board IMG board LGC board HDD Page memory
Remedy: Other • Remove the paper remained in front of the registration sensor) • Check if the error is cleared by turning the power OFF and then back ON. SYS board • Connector check • Board check IMG board • Connector check • Board check LGC board • Connector check • Board check HDD • Connector check • HDD check Page memory Check if the page memory is correctly connected to the connector on the SYS board.

Code: E064

Description: Incorrect paper size setting for PFP lower drawer: The size of paper in the 4th drawer differs from size setting of the equipment.
Causes: SYS board IMG board LGC board HDD Page memory
Remedy: Other • Remove the paper remained in front of the registration sensor) • Check if the error is cleared by turning the power OFF and then back ON. SYS board • Connector check • Board check IMG board • Connector check • Board check LGC board • Connector check • Board check HDD • Connector check • HDD check Page memory Check if the page memory is correctly connected to the connector on the SYS board.

Code: E065

Description: Incorrect paper size setting for bypass tray: The size of paper in the bypass tray differs from size setting of the equipment.
Causes: SYS board IMG board LGC board HDD Page memory
Remedy: Other • Remove the paper remained in front of the registration sensor) • Check if the error is cleared by turning the power OFF and then back ON. SYS board • Connector check • Board check IMG board • Connector check • Board check LGC board • Connector check • Board check HDD • Connector check • HDD check Page memory Check if the page memory is correctly connected to the connector on the SYS board.

Code: E090

Description: Image data delay jam: Image data to be printed cannot be prepared
Causes: SYS board IMG board LGC board HDD Page memory
Remedy: Other • Remove the paper remained in front of the registration sensor) • Check if the error is cleared by turning the power OFF and then back ON. SYS board • Connector check • Board check IMG board • Connector check • Board check LGC board • Connector check • Board check HDD • Connector check • HDD check Page memory Check if the page memory is correctly connected to the connector on the SYS board.

Code: E091

Description: Motor-ON time-out jam: The equipment does not operate normally because abnormality occurred on an interface between the SYS board and engine firmware.
Causes: SYS board IMG board LGC board HDD
Remedy: Other • Check if there is any paper in the equipment. Remove it if there is. • If the error still occurs, check the following. Power Check if the error is cleared by turning the power OFF and then back ON. SYS board • Connector check • Board check IMG board • Connector check • Board check LGC board • Connector check • Board check HDD • Connector check • HDD check

Code: E0A0

Description: Image transport ready time-out jam: Image data to be printed cannot be sent.
Causes: LGC board
Remedy: LGC board Connector check

Code: E110

Description: ADU misfeeding (Paper not reaching the registration sensor): The paper which has passed through ADU does not reach the registration sensor during duplex printing.
Causes: Registration sensor LGC board ADU clutch Rollers in the ADU
Remedy: Paper stop jam at the registration roller position Registration guide Check the registration guide. Replace it if needed. All Registration sensor • Sensor check (Perform the input check: 03- [ALL]OFF/[7]/[F]) • Connector check (CN337) • Harness check LGC board • Board check • Connector check (CN337, CN338) • Harness check ADU clutch • Clutch check (Perform the output check: 03- 222) • Connector check (CN338) • Harness check ADU Check if the connector between the ADU and equipment is connected.

Code: E120

Description: Bypass misfeeding (Paper not reaching the bypass feed sensor): Paper fed from the bypass tray does not reach the bypass feed sensor.
Causes: Bypass feed clutch Bypass feed sensor LGC board
Remedy: Bypass feed clutch • Clutch check (Perform the output check: 03-204 and the input check: 03-[FAX]ON/[4]/[D]) • Connector check (CN338) • Harness check Bypass feed sensor • Sensor check (Perform the output check: 03-204 and the input check: 03-[FAX]ON/[4]/[D]) • Connector check (CN338) • Harness check LGC board • Board check • Connector check (CN338) • Harness check
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie