• Code: EAFA
• Description: Catching motor home position detection error (paper jam)
• Causes:
• Remedy:

• Code: EAFB
• Description: [MJ-1109/1110] Stapler movement error (paper jam)
• Causes: Stapler unit home position sensor (S10) Stapler unit shift motor (M9) Finisher control PC board (FIN)
• Remedy: Stapler Move the stapler. Fix any mechanical problem. Stapler unit home position sensor (S10) Check if there is a disconnection of the connector, incorrect installation or breakage of the stapler unit home position sensor (S10). If there is, reinstall the sensor correctly or replace it. Check if the connector (CN27) on the finisher controller PC board is disconnected from the stapler unit home position sensor (S10) and the harnesses are open circuited. Correct if so. Stapler unit shift motor (M9) Check if the connector (CN15) on the finisher control PC board is disconnected from the stapler unit shift motor (M9) and the harnesses are open circuited. Correct if so.

• Code: EAFC
• Description: [MJ-1109/1110] Movable tray height error (paper jam)
• Causes:
• Remedy:

• Code: EAFD
• Description: [MJ-1109/1110] Movable tray movement error (paper jam)
• Causes: Movable tray paper-full sensor (S16) Movable tray position A, B, and C sensors (S13, S14 and S15) Finisher control PC board (FIN)
• Remedy: Movable tray paper-full sensor (S16) Fix any mechanical problem occurring when the actuator is moved. Check if there is a disconnection of the connector, incorrect installation or breakage of the movable tray paper-full sensor (S16). If there is, reinstall the sensor correctly or replace it. Check if the connector (CN22) on the finisher controller PC board is disconnected from the movable tray paper-full sensor (S16) and the harnesses are open circuited. Correct if so. Movable tray position A, B, and C sensors (S13, S14 and S15) • Connector check (CN20) • Sensor check • Harness check

• Code: EAFE
• Description: [MJ-1109/1110] Paper holding cam position error (paper jam)
• Causes: Assist arm motor (M10) Finisher control PC board (FIN)
• Remedy: Paper pusher cam • Is there any mechanical problem when the paper pusher cam is rotated? Assist arm motor (M10) • Motor check • Connector check (CN10) • Harness check Finisher control PC board (FIN) • Connector check (CN10) • Board check

• Code: EB30
• Description: Ready time-out jam
• Causes: LGC board
• Remedy: Finisher Check if the connector on the equipment is disconnected from the finisher or the harnesses are open circuited. Correct if any.

• Code: EB50
• Description: Paper remaining jam on the transport path
• Causes: Feed sensor PFC board LGC board Separation roller Replace it if it is worn out.
• Remedy: Feed sensor • Sensor check (Perform the input check: FS-03-[ALL]OFF/[9]/[B]) • Connector check (CN458, J659, J661) • Harness check PFC board • Board check • Connector check (CN458, CN461, CN452) • Harness check LGC board • Board check • Connector check (CN323) • Harness check

• Code: EB60
• Description: Paper remaining jam on the transport path
• Causes: Registration sensor PFC board LGC board Rollers Replace it if it is worn out.
• Remedy: Registration sensor • Sensor check (Perform the input check: FS-03-[ALL]OFF/[9]/[A]) • Connector check (CN458, J659, J660) • Harness check PFC board • Board check • Connector check (CN458, CN452, CN461) • Harness check LGC board • Connector check (CN323) • Board check Drive unit, Rollers • Gear check • Roller check