Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Toshiba e-Studio 356S — Trang 18/33

Code: E722

Description: Jam not reaching the exit sensor (during scanning): The original which passed the read sensor does not reach the exit sensor when it is transported from the scanning section to exit section.
Causes: Original exit/reverse sensor RADF board Read roller Replace it if it is worn out.
Remedy: Read roller Clean the read roller if it is stained. Original exit/reverse sensor • Sensor check (Perform the input check: 03-[FAX] ON[7]/[E]) • Connector check (CN75) • Harness check RADF board • Board check • Connector check (CN75) • Harness check

Code: E724

Description: Stop jam at the registration sensor: The trailing edge of the original does not pass the registration sensor after its leading edge has reached this sensor.
Causes: Registration sensor RADF board Registration roller Replace it if it is worn out.
Remedy: Registration roller Clean the registration roller if it is stained. Registration sensor • Sensor check (Perform the input check: 03-[FAX] ON[7]/[H]) • Connector check (CN74) • Harness check RADF board • Board check • Connector check (CN74) • Harness check

Code: E725

Description: Stop jam at the read sensor: The trailing edge of the original does not pass the read sensor after its leading edge has reached this sensor.
Causes: Read ensor RADF board Read roller Replace it if it is worn out.
Remedy: Read roller Clean the registration roller if it is stained. Read sensor • Sensor check (Perform the input check: 03-[FAX] ON[7]/[G]) • Connector check (CN75) • Harness check RADF board • Board check • Connector check (CN75) • Harness check

Code: E726

Description: Transport/exit signal reception jam: RADF receives the transport/exit reception signal from the equipment when no original is at the exposure waiting position.
Causes: RADF board SLG board Switching regulator
Remedy: RADF board • Board check • Connector check • Harness check SLG board • Board check • Connector check • Harness check Switching power supply • Check if the 24V and 5V outputs of the switching power supply are normal. • Board check • Connector check • Harness check

Code: E731

Description: Stop jam at the exit sensor: The trailing edge of the original does not pass the exit sensor after its leading edge has reached this sensor.
Causes: Exit sensor RADF board Exit roller Replace it if it is worn out.
Remedy: Exit roller Clean the registration roller if it is stained. Exit sensor • Sensor check (Perform the input check: 03-[FAX] ON[7]/[E]) • Connector check (CN74) • Harness check RADF board • Board check • Connector check (CN74) • Harness check

Code: E860

Description: RADF jam access cover open: The RADF jam access cover has opened during RADF operation.
Causes: RADF jam access cover switch RADF board
Remedy: RADF jam access cover Close the RADF jam access cover if it is opened. Remove if there is any original before closing it. RADF jam access cover switch • Sensor check (Perform the input check: 03-[FAX] ON[7]/[C]) • Connector check (CN8) • Harness check RADF board • Board check • Connector check (CN8) • Harness check

Code: E870

Description: RADF open jam: RADF has opened during RADF operation.
Causes: RADF opening/closing sensor Is the RADF opening/closing sensor adjusted within the specified range? RADF board
Remedy: RADF Close the RADF if it is opened. Remove if there is any original before closing it. RADF opening/closing sensor • Sensor check (Perform the input check: 03-[FAX] ON[7]/[D]) • Connector check (CN75) • Harness check RADF board • Board check • Connector check (CN75) • Harness check

Code: E871

Description: Cover open jam in the read ready status: Jam caused by opening of the RADF jam access cover or front cover while the RADF is waiting for the scanning start signal from the equipment.
Causes: RADF jam access cover sensor RADF board
Remedy: RADF jam access cover Front cover Close the RADF jam access cover or the front cover if they are opened in the read ready status. RADF jam access cover sensor • Sensor check (Perform the input check: 03-[FAX] ON[7]/[C]) • Connector check (CN75) • Harness check
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie