Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Toshiba e-Studio 457SD — Trang 26/33

Code: EF13

Description: Saddle paper holder home position detection abnormality: The paper holder home position cannot be detected. [MJ-1106]
Causes: Paper holding home position sensor (S38) Saddle controller board
Remedy: Finisher • Is there any mechanical problem when the paper holding cam is rotated? Paper holding home position sensor (S38) • Sensor check • Connector check • Harness check Saddle controller board • Connector check (CN8) • Board check

Code: EF14

Description: Saddle paper exit jam: Outputting paper is not completed within a fixed time. [MJ-1106]
Causes: MJ-1106 Exit sensor (S31) Saddle controller board
Remedy: MJ-1106 Finisher • Is there any paper remaining in the paper transport path of the equipment or the saddle stitch section of the Finisher? Exit sensor (S31) • Sensor check • Connector check • Harness check Saddle controller board • Connector check (CN19) • Board check
MJ-1033 Saddle stitch finishing tray sensor (S7) abnormality Measure the voltage on TP65 on the finisher control PC board (FIN). Then check that the measured voltage is 1V or lower when not shielded and within the range of 3.3V±5% when shielded. If the voltage does not fall within the range mentioned, replace the sensor. Saddle stitch exit path sensor (S5) abnormality Measure the voltage on TP68 on the finisher control PC board (FIN). Then check that the measured voltage is 1V or lower when not shielded and within the range of 3.3V±5% when shielded. If the voltage does not fall within the range mentioned, replace the sensor. Faulty cables and connectors Check if the electrical continuity between the connector terminals is normal. If electricity is not conducted, replace the connectors. (Finisher control PC board (FIN): CN15, CN16) Finisher control PC board (FIN) abnormality If the error still occurs after replacing the sensors and the connectors, exchange the finisher control PC board (FIN).

Code: EF15

Description: Saddle Stitch Finisher side alignment motor home position detection abnormality: The side alignment motor home position cannot be detected. [MJ-1106]
Causes: Side alignment home position sensor (S36) Side alignment motor (M15) Saddle controller board
Remedy: Finisher • Is there any mechanical problem when the jog is moved? Side alignment home position sensor (S36) • Sensor check • Connector check • Harness check Side alignment motor (M15) • Motor check • Connector check • Harness check Saddle controller board • Connector check (CN5) • Board check

Code: EF16

Description: Saddle Stitch Finisher stacker motor home position detection abnormality: The stacker motor home position cannot be detected. [MJ-1106]
Causes: Stacker home position sensor (S33) Stacker motor (M14) Saddle controller board
Remedy: Stacker carrier • Is there any mechanical problem when the stacker carrier is moved? Stacker home position sensor (S33) • Sensor check • Connector check • Harness check Stacker motor (M14) • Motor check • Connector check • Harness check Saddle controller board • Connector check (CN4) • Board check

Code: EF17

Description: Saddle Stitch Finisher folding blade home position detection abnormality: The folding blade home position cannot be detected. [MJ-1106]
Causes: Folding blade home position sensor (S35) Folding blade clutch (CLT3) Saddle controller board
Remedy: Folding blade cam • Is there any mechanical problem when the folding blade cam is rotated? Folding blade home position sensor (S35) • Sensor check • Connector check • Harness check Folding blade clutch (CLT3) • Clutch check • Connector check • Harness check Saddle controller board • Connector check (CN15) • Board check

Code: EF18

Description: Saddle Stitch Finisher additional folding roller home position detection abnormality: The additional folding roller home position cannot be detected. [MJ-1106]
Causes: Additional folding home position sensor (S39) Additional folding motor (M20) Saddle controller board
Remedy: Additional folding carrier • Is there any mechanical problem when the additional folding carrier is moved? Additional folding home position sensor (S39) • Sensor check • Connector check • Harness check Additional folding motor (M20) • Motor check • Connector check • Harness check Saddle controller board • Connector check (CN18, CN19) • Board check

Code: EF19

Description: Saddle paper folding jam: Fold processed paper cannot be transported to the additional folding roller. [MJ-1106]
Causes: Exit transport sensor (S41) Saddle controller board
Remedy: Finisher • Is there any paper remaining in the paper transport path in the equipment or the saddle stitch section of the Finisher? Exit transport sensor (S41) • Sensor check • Connector check • Harness check Saddle controller board • Connector check (CN19) • Board check

Code: EF1A

Description: The trailing edge of the paper passed the entrance path sensor on the Finisher unit transport path. After the switchback, the paper is transported to the saddle stitch unit transport path, but does not reach the saddle stitch entrance path sensor.
Causes:
Remedy:
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie