Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Toshiba e-Studio 520 — Trang 8/29

Code: CAA0

Description: Secondary scanning fine adjustment error: Secondary scanning control by the galvanometer mirror does not end normally. [e-STUDIO850]
Remedy: Is any harness between the PLG board and galvanic mirror, PLG board and laser drive PC board and PLG board and H-Sync detection PC board open circuited or any connector disconnected? → YES . Replace the harness. Reconnect the connector. NO 1) Replace the PLG board. 2) Replace the laser optical unit.

Code: CAB0

Description: Inter-page correction error of secondary scanning: Inter-page secondary scanning control by the galvanometer mirror does not end normally. [e-STUDIO850]
Remedy: Is any harness between the PLG board and galvanic mirror, PLG board and laser drive PC board and PLG board and H-Sync detection PC board open circuited or any connector disconnected? → YES . Replace the harness. Reconnect the connector. NO 1) Replace the PLG board. 2) Replace the laser optical unit.

Code: CAC0

Description: Primary scanning dot adjustment error: Primary scanning control does not end normally. [e-STUDIO850]
Remedy: Is any harness between the PLG board and galvanic mirror, PLG board and laser drive PC board and PLG board and H-Sync detection PC board open circuited or any connector disconnected? → YES . Replace the harness. Reconnect the connector. NO 1) Replace the PLG board. 2) Replace the laser optical unit.

Code: CAF0

Description: Inter-page correction error of primary scanning: Inter-page primary scanning control does not end normally. [e-STUDIO850]
Remedy: Is any harness between the PLG board and galvanic mirror, PLG board and laser drive PC board and PLG board and H-Sync detection PC board open circuited or any connector disconnected? → YES . Replace the harness. Reconnect the connector. NO 1) Replace the PLG board. 2) Replace the laser optical unit.

Code: CB10

Description: Feed motor abnormality: The feed motor does not run normally or the stack feed roller does not move normally.
Remedy: [Procedure 1] Is second feed motor (M8) rotating in reverse at the fixed timing? → NO . Replace second feed motor or finisher controller PC board. YES Is the shutter securely attached to the shutter upper/lower bars? → NO . Attach it securely. YES Turn the feed roller-2 in reverse by hand. Do the shutter upper/lower bars move up and down? l → NO . Fix the mechanism including the shutter upper/lower bars and gears of the feed roller-2. YES Is the shutter closed detecting switch (MS4) working normally? → NO . Replace the switch. YES Replace the finisher controller PC board. [Procedure 2] Is second feed motor (M8) rotating in reverse at the fixed timing? → NO . Replace second feed motor or finisher controller PC board. YES Is the shutter securely attached to the shutter upper/lower bars? → NO . Attach it securely. YES Turn feed roller-2 in reverse by hand. Do the shutter upper/lower bars move up and down? l → NO . Fix the mechanism including the shutter upper/lower bars and gears of the feed roller-2. YES Is the shutter open sensor (PI5) working normally? → NO . Replace the sensor. YES Replace the finisher controller PC board. [Procedure 3] Check the safety zone switch (MS3). Is the switch working normally? → NO . Replace the switch. YES Is the safety zone switch (MS3) correctly pressed? → NO . Fix the mechanism. YES Is the shutter closed detecting switch (MS4) working normally? → NO . Replace the switch. YES Is the shutter closed detecting switch (MS4) correctly pressed? → NO . Fix the mechanism. YES Replace the finisher controller PC board.

Code: CB20

Description: Delivery motor abnormality: The delivery motor does not run normally or the delivery roller does not move normally.
Remedy: Rotate the delivery motor by hand. Does it rotate smoothly? → NO. Fix the mechanism. YES Is the delivery motor clock sensor (PI10) working normally? → NO. Replace the sensor. YES Does the voltage between J11-4 and -5 on the finisher controller PC board become 24V when the delivery motor starts rotating? → NO. Replace the finisher controller PC board. YES Is the wiring between the delivery motor and finisher controller PC board correct? → YES. Correct the wiring. NO Replace the motor.

Code: CB30

Description: Tray lift motor abnormality
Remedy: [Procedure 1] Is the tray 1 home position sensor (PI8) working properly? → NO. Replace the tray 1 home position sensor. YES Is the tray 1 lifting mechanism working properly? → NO. Correct the defect of the mechanism. YES Is 24V supplied to the tray1 lifting motor (M5) from the finisher control board at the timing of tray driving? → NO. Replace the finisher control board. YES Is the harness between the finisher control board and tray 1 lifting motor normal? → NO. Replace the harness. YES Replace the tray 1 lifting motor. [Procedure 2] Is the tray 1 lifted/lowered? ↓ → YES . Is the wiring between the finisher controller PC board and tray 1 lifting motor normal? → NO. Correct the wiring. YES Replace the tray 1 lifting motor. NO Is the power supplied to the motor from the finisher control board at the timing of tray 1 lifting? → NO. Replace the finisher control board. YES Is there any abnormality at the tray 1 lifting mechanism? → YES . Correct the defect of the mechanism. YES Correct the defect of the mechanism. [Procedure 3] Is the tray 2 home position sensor (PI25) working properly? → NO. Replace the tray 2 home position sensor. YES Is the tray 2 lifting mechanism working properly? → NO. Correct the defect of the mechanism. YES Is 24V supplied to the tray 2 lifting motor (M10) from the finisher control board at the timing of tray driving? → NO. Replace the finisher control board. YES Is the harness between the finisher control board and tray 2 lifting motor normal? → NO. Replace the harness. YES Replace the tray 2 lifting motor. [Procedure 4] Is the tray 2 lifted/lowered? ↓ → YES . Is the harness between the finisher control board and tray 2 lifting motor normal? → NO. Correct the wiring. YES Replace the tray 2 lifting motor. NO Is the power supplied to the motor from the finisher control board at the timing of tray 2 lifting? → NO. Replace the finisher control board. YES Is there any abnormality at the tray 2 lifting mechanism? → YES . Correct the defect of the mechanism. NO Replace the tray 2 lifting motor. [Procedure 5] Is the tray lifting mechanism working properly? → NO . Correct the defect of the mechanism. YES Is the tray coming close detection switch working properly? → NO. Replace the switch. YES Replace the finisher controller PC board.

Code: CB40

Description: Alignment motor (rear) abnormality: The alignment motor (rear) does not run normally or the alignment plate does not move normally.
Remedy: Is the alignment guide home position sensor (PI5S) working normally? → NO. Replace the sensor. YES Is the wiring between the finisher controller PC board and the alignment motor (M5S) correct? → YES. Correct the wiring. NO Is there any mechanical problem with the alignment guide movement path? → YES. Fix the mechanism. NO Is the problem solved by replacing the alignment motor? → NO. Replace the finisher controller PC board. YES END
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie