Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Toshiba e-Studio 5560C — Trang 21/44

Code: E090

Description: Image data delay jam: Image data to be printed cannot be prepared.
Causes: SYS board IMG board LGC board HDD Page memory
Remedy: Other • Remove the paper remained in front of the registration sensor. • If the error still occurs, check the following. Power • Check if the error is cleared by turning the power OFF and then back ON SYS board • Connector check (SYS board -IMG board) (CN135) • Page memory check • Board check IMG board • Connector check (IMG board -SLG board) (IMG board - LGC board) (CN422, CN423, CN424) • Harness check • Board check LGC board • Connector check (CN319, CN320) • Harness check • Board check HDD • Connector check • HDD check Page memory Check if the page memory is correctly connected to the connector on the SYS board

Code: E091

Description: Motor-ON time-out jam: The equipment does not operate normally because abnormality occurred on an interface between the SYS board and engine firmware.
Causes: SYS board IMG board LGC board HDD
Remedy: Other • Check if there is any paper in the equipment. Remove it if there is. • If the error still occurs, check the following. Power Check if the error is cleared by turning the power OFF and then back ON. SYS board • Connector check (SYS board -IMG board) (CN135) • Board check IMG board • Connector check (IMG board -SLG board) (IMG board - LGC board) (CN422, CN423, CN424) • Harness check • Board check LGC board • Connector check (CN319, CN320) • Harness check • Board check HDD • Connector check • HDD check

Code: E0A0

Description: Image transport ready time-out jam: Image data to be printed cannot be sent.
Causes: SYS board IMG board LGC board HDD
Remedy: Other • Remove the paper remained in front of the registration sensor. • If the error still occurs, check the following. Power Check if the error is cleared by turning the power OFF and then back ON. SYS board • Connector check (SYS board -IMG board) (CN135) • Board check IMG board • Connector check (IMG board -SLG board) (IMG board - LGC board) (CN422, CN423, CN424) • Harness check • Board check LGC board • Connector check (CN319, CN320) • Harness check • Board check HDD • Connector check • HDD check

Code: E110

Description: ADU misfeeding (Paper not reaching the registration sensor): The paper which has passed through ADU does not reach the registration sensor during duplex printing.
Causes: Registration sensor ADU motor2 ADU board PFC board LGC board ADU roller
Remedy: Registration sensor • Sensor check (Perform the input check: 03-[ALL]OFF/[4]/[B], 03-[COPY]ON/[5]/[H]) • Connector check • Harness check ADU motor2 • Motor check (Perform the output check: 03-144) • Connector check (CN491, CN495) • Harness check LGC board • Connector check (CN309) • Board check Drive unit, Rollers • Gear check • Roller check PFC board • Connector check (CN500, CN515) • Harness check • Board check

Code: E120

Description: Bypass misfeeding (Paper not reaching the bypass feed sensor): Paper fed from the bypass tray does not reach the bypass feed sensor.
Causes: Bypass feed sensor Bypass motor Bypass pick-up solenoid ADU board PFC board ADU roller Rollers
Remedy: Bypass feed sensor • Sensor check (Perform the input check: 03-[SCAN]ON/[3]/[A]) • Connector check • Harness check Bypass motor • Motor check (Perform the output check: 03-126) • Connector check • Harness check Bypass pick-up solenoid • Solenoid check (Perform the output check: 03-1254) • Connector check • Harness check ADU board • Connector check (CN490, CN496, CN498) • Board check PFC board • Connector check (CN509) • Harness check • Board check Drive unit, Rollers • Gear check • Roller check

Code: E130

Description: 1st drawer misfeeding (Paper not reaching the 1st drawer feed sensor): The paper fed from the 1st drawer does not reach the 1st drawer feed sensor.
Causes: 1st drawer feed sensor Feed motor PFC roller Rollers
Remedy: 1st drawer feed sensor • Sensor check (Perform the input check: 03-[SCAN]ON/[1]/[H]) • Connector check • Harness check Feed motor • Motor check (Perform the output check: 03-120) • Connector check • Harness check PFC board • Connector check (CN512, CN513) • Board check Drive unit, Rollers • Gear check • Roller check

Code: E140

Description: 2nd drawer misfeeding (Paper not reaching the 2nd drawer feed sensor): The paper fed from the 2nd drawer does not reach the 2nd drawer feed sensor.
Causes: 2nd drawer feed sensor Feed motor PFC roller Rollers
Remedy: 2nd drawer feed sensor • Sensor check (Perform the input check: 03-[SCAN]ON/[1]/[G]) • Connector check • Harness check Feed motor • Motor check (Perform the output check: 03-121) • Connector check • Harness check PFC board • Connector check (CN512, CN513) • Board check Drive unit, Rollers • Gear check • Roller check

Code: E150

Description: 3rd drawer misfeeding (Paper not reaching the 3rd drawer feed sensor): The paper fed from the 3rd drawer does not reach the 3rd drawer feed sensor
Causes: 3rd drawer feed sensor Feed/transfer motor PFC roller Rollers 3rd drawer feed clutch
Remedy: 3rd drawer feed sensor • Sensor check (Perform the input check: 03-[SCAN]ON/[1]/[F]) • Connector check • Harness check Feed/transfer motor • Motor check (Perform the output check: 03-122) • Connector check • Harness check 3rd drawer feed clutch • Clutch check (Perform the output check: 03-250) • Connector check • Harness check PFC board • Connector check (CN502, CN505) • Board check Drive unit, Rollers • Gear check • Roller check
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie