Description: Stop jam at the original exit/reverse sensor: The trailing edge of the original does not pass the original exit/reverse sensor after its leading edge has reached this sensor.
Causes: Original exit sensor RADF board Perform the 05-3210 Roller Exit roller
Description: Exit/reverse sensor paper remaining jam
Causes: Original exit reverse sensor Registration sensor Original width detection sensor-1 Original width detection sensor-2 Original width detection sensor-3 Intermediate transport sensor Reading end sensor Exit sensor RADF board Perform the 05-3210 Roller
Remedy: RADF • Check if there is any paper on each sensor. Remove it if there is. Original exit reverse sensor • Sensor check (Perform the input check: 03: [FAX]/ON/[5]/[B]) • Connector check • Harness check Registration sensor • Sensor check (Perform the input check: 03: [FAX]/ON/[8]/[F]) • Connector check • Harness check Original width detection sensor-1 • Sensor check (Perform the input check: 03: [FAX]/ON/[7]/[F]) • Connector check • Harness check Original width detection sensor-2 • Sensor check (Perform the input check: 03: [FAX]/ON/[8]/[H]) • Connector check • Harness check Original width detection sensor-3 • Sensor check (Perform the input check: 03: [FAX]/ON/[5]/[D]) • Connector check • Harness check Intermediate transport sensor • Sensor check (Perform the input check: 03: [FAX]/ON/[8]/[G]) • Connector check • Harness check Reading end sensor • Sensor check (Perform the input check: 03: [FAX]/ON/[7]/[F]) • Connector check • Harness check Exit sensor • Sensor check (Perform the input check: 03: [FAX]/ON/[7]/[E]) • Connector check • Harness check RADF board • Connector check (CN74, CN75) • Board check Drive unit, Rollers • Gear check • Roller check
Description: Registration sensor paper remaining jam
Causes: Original exit reverse sensor Registration sensor Original width detection sensor-1 Original width detection sensor-2 Original width detection sensor-3 Intermediate transport sensor Reading end sensor Exit sensor RADF board Perform the 05-3210 Roller
Remedy: RADF • Check if there is any paper on each sensor. Remove it if there is. Original exit reverse sensor • Sensor check (Perform the input check: 03: [FAX]/ON/[5]/[B]) • Connector check • Harness check Registration sensor • Sensor check (Perform the input check: 03: [FAX]/ON/[8]/[F]) • Connector check • Harness check Original width detection sensor-1 • Sensor check (Perform the input check: 03: [FAX]/ON/[7]/[F]) • Connector check • Harness check Original width detection sensor-2 • Sensor check (Perform the input check: 03: [FAX]/ON/[8]/[H]) • Connector check • Harness check Original width detection sensor-3 • Sensor check (Perform the input check: 03: [FAX]/ON/[5]/[D]) • Connector check • Harness check Intermediate transport sensor • Sensor check (Perform the input check: 03: [FAX]/ON/[8]/[G]) • Connector check • Harness check Reading end sensor • Sensor check (Perform the input check: 03: [FAX]/ON/[7]/[F]) • Connector check • Harness check Exit sensor • Sensor check (Perform the input check: 03: [FAX]/ON/[7]/[E]) • Connector check • Harness check RADF board • Connector check (CN74, CN75) • Board check Drive unit, Rollers • Gear check • Roller check
Description: Original width detection sensor-1 paper remaining jam
Causes: Original exit reverse sensor Registration sensor Original width detection sensor-1 Original width detection sensor-2 Original width detection sensor-3 Intermediate transport sensor Reading end sensor Exit sensor RADF board Perform the 05-3210 Roller
Remedy: RADF • Check if there is any paper on each sensor. Remove it if there is. Original exit reverse sensor • Sensor check (Perform the input check: 03: [FAX]/ON/[5]/[B]) • Connector check • Harness check Registration sensor • Sensor check (Perform the input check: 03: [FAX]/ON/[8]/[F]) • Connector check • Harness check Original width detection sensor-1 • Sensor check (Perform the input check: 03: [FAX]/ON/[7]/[F]) • Connector check • Harness check Original width detection sensor-2 • Sensor check (Perform the input check: 03: [FAX]/ON/[8]/[H]) • Connector check • Harness check Original width detection sensor-3 • Sensor check (Perform the input check: 03: [FAX]/ON/[5]/[D]) • Connector check • Harness check Intermediate transport sensor • Sensor check (Perform the input check: 03: [FAX]/ON/[8]/[G]) • Connector check • Harness check Reading end sensor • Sensor check (Perform the input check: 03: [FAX]/ON/[7]/[F]) • Connector check • Harness check Exit sensor • Sensor check (Perform the input check: 03: [FAX]/ON/[7]/[E]) • Connector check • Harness check RADF board • Connector check (CN74, CN75) • Board check Drive unit, Rollers • Gear check • Roller check
Description: Original width detection sensor-2 paper remaining jam
Causes: Original exit reverse sensor Registration sensor Original width detection sensor-1 Original width detection sensor-2 Original width detection sensor-3 Intermediate transport sensor Reading end sensor Exit sensor RADF board Perform the 05-3210 Roller
Remedy: RADF • Check if there is any paper on each sensor. Remove it if there is. Original exit reverse sensor • Sensor check (Perform the input check: 03: [FAX]/ON/[5]/[B]) • Connector check • Harness check Registration sensor • Sensor check (Perform the input check: 03: [FAX]/ON/[8]/[F]) • Connector check • Harness check Original width detection sensor-1 • Sensor check (Perform the input check: 03: [FAX]/ON/[7]/[F]) • Connector check • Harness check Original width detection sensor-2 • Sensor check (Perform the input check: 03: [FAX]/ON/[8]/[H]) • Connector check • Harness check Original width detection sensor-3 • Sensor check (Perform the input check: 03: [FAX]/ON/[5]/[D]) • Connector check • Harness check Intermediate transport sensor • Sensor check (Perform the input check: 03: [FAX]/ON/[8]/[G]) • Connector check • Harness check Reading end sensor • Sensor check (Perform the input check: 03: [FAX]/ON/[7]/[F]) • Connector check • Harness check Exit sensor • Sensor check (Perform the input check: 03: [FAX]/ON/[7]/[E]) • Connector check • Harness check RADF board • Connector check (CN74, CN75) • Board check Drive unit, Rollers • Gear check • Roller check
Description: Original width detection sensor-3 paper remaining jam
Causes: Original exit reverse sensor Registration sensor Original width detection sensor-1 Original width detection sensor-2 Original width detection sensor-3 Intermediate transport sensor Reading end sensor Exit sensor RADF board Perform the 05-3210 Roller
Remedy: RADF • Check if there is any paper on each sensor. Remove it if there is. Original exit reverse sensor • Sensor check (Perform the input check: 03: [FAX]/ON/[5]/[B]) • Connector check • Harness check Registration sensor • Sensor check (Perform the input check: 03: [FAX]/ON/[8]/[F]) • Connector check • Harness check Original width detection sensor-1 • Sensor check (Perform the input check: 03: [FAX]/ON/[7]/[F]) • Connector check • Harness check Original width detection sensor-2 • Sensor check (Perform the input check: 03: [FAX]/ON/[8]/[H]) • Connector check • Harness check Original width detection sensor-3 • Sensor check (Perform the input check: 03: [FAX]/ON/[5]/[D]) • Connector check • Harness check Intermediate transport sensor • Sensor check (Perform the input check: 03: [FAX]/ON/[8]/[G]) • Connector check • Harness check Reading end sensor • Sensor check (Perform the input check: 03: [FAX]/ON/[7]/[F]) • Connector check • Harness check Exit sensor • Sensor check (Perform the input check: 03: [FAX]/ON/[7]/[E]) • Connector check • Harness check RADF board • Connector check (CN74, CN75) • Board check Drive unit, Rollers • Gear check • Roller check
Nhận ưu đãi sớm nhất khi chương trình diễn ra
Đăng ký nhận bản tin
Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này.
Chính sách cookie
Những cookie này là cần thiết để trang web hoạt động đúng cách.
Những cookie này giúp chúng tôi hiểu cách khách truy cập tương tác với trang web.
Những cookie này được sử dụng để cung cấp quảng cáo cá nhân hóa.