Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Xerox WorkCentre 5735 — Trang 10/27

Code: 08-106

Description: Lead Edge Late to Tray 1 Feed Sensor RAP 08-106 The lead edge of the paper was late to tray 1 feed sensor when feeding from tray 2. The fault will also occur when feeding from tray 3 or tray 4 providing the trail edge of the sheet has cleared the tray 4 feed sensor.
Remedy: NOTE: The front door interlock must be cheated when checking +24V components. Enter dC330 code 08-101 tray 1 feed sensor, Q08-101. Press Start. Open the left hand door and manually actuate the sensor. The display changes. Y↓N→Go to Flag 1. Check Q08-101. Refer to: • Component location. • GP 11 How to Check a Sensor. • P/J276, Tray 1 and 2 control PWB. • 01E +5V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Tray 1 feed sensor, PL 7.30 Item 24. • Tray 1 and 2 control PWB, PL 7.10 Item 2. Enter dC330 code 08-102 tray 2 feed sensor, Q08-102. Press Start. Manually actuate the sensor. The display changes. Y↓N→Go to Flag 2. Check Q08-102. Refer to: • GP 11 How to Check a Sensor. • P/J276, Tray 1 and 2 control PWB. • 01E +5V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Tray 2 feed sensor, PL 7.30 Item 24. • Tray 1 and 2 control PWB, PL 7.10 Item 2. Enter dC330 code 08-025 transport roll drives motor, MOT08-025. Press Start. The motor runs. Y↓N→Go to Flag 3. Check MOT08-025. Refer to: • GP 10 How to Check a Motor. • P/J273, Tray 1 and 2 control PWB. • 01G +24V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Transport roll drives motor, PL 8.25 Item 5. • Tray 1 and 2 control PWB, PL 7.10 Item 2. The transport rolls rotate. Y↓N→Check the drive belt and pulleys, PL 8.25 Item 2, PL 8.25 Item 3. Check the following: • The bearing, shaft and rolls on the transport roll assembly, GP 7, PL 8.25 Item 8. • The idler rolls in the left hand door, GP 7, PL 7.30 Item 2. • The transport drive belt, PL 8.25 Item 2. • If the fault occurs when feeding from tray 3 or tray 4 but not tray 2 then check the positioning of the tray 3 / 4 transport pinch rolls, PL 8.30 Item 18, and the transport motor bracket, PL 8.30 Item 14. Install new components as necessary.

Code: 08-107

Description: Tray 3 Paper Feed Jam RAP (W/O TAG 151) 08-107 The lead edge of the paper was late to tray 4 feed sensor when feeding from tray 3.
Remedy: NOTE: The front door interlock must be cheated when checking +24V components. Enter dC330 code 08-104 tray 4 feed sensor, Q08-104. Press Start. Manually actuate the tray 4 sensor. The display changes. Y↓N→Go to Flag 1. Check Q08-104. Refer to: • GP 11 How to Check a Sensor. • P/J392, HCF control PWB. • 01E +5V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Tray 4 feed sensor, PL 8.31 Item 12. • HCF control PWB, PL 7.20 Item 2. Enter dC330 code 08-045 tray 3 and 4 transport motor, MOT08-045. Press Start. The motor runs. Y↓N→Go to Flag 2. Check MOT08-045. Refer to: • GP 10 How to Check a Motor. • P/J398, HCF control PWB. • 01G +24V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Tray 3 and 4 transport motor, PL 8.30 Item 7. • HCF control PWB, PL 7.20 Item 2. The transport rolls rotate. Y N. Check the drive belt and drive coupling, PL 8.30 Item 9. Perform the following: •. Check the tray 3 transport rolls, PL 8.35, PL 8.30. • Go to RAP 08-103, 08-113 Tray 3 Misfeed RAP.

Code: 08-108

Description: Tray 3 or Tray 4 Paper Feed Jam RAP (W/O TAG 151) 08-108 The lead edge of the paper was late to tray 2 feed sensor when feeding from tray 3 or tray 4.
Remedy: NOTE: The front door interlock must be cheated when checking +24V components. Enter dC330 code 08-102 tray 2 feed sensor, Q08-102. Press Start. Manually actuate the sensor. The display changes. Y↓N→Go to Flag 1. Check Q08-102. Refer to: • GP 11 How to Check a Sensor. • P/J276, Tray 1 and 2 control PWB. • 01E +5V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Tray 2 feed sensor, PL 7.30 Item 24. • Tray 1 and 2 control PWB, PL 7.10 Item 2. Enter dC330 code 08-045 tray 3 and 4 transport motor, MOT08-045. Press Start. The motor runs. Y↓N→Go to Flag 2. Check MOT08-045. Refer to: • GP 10 How to Check a Motor. • P/J398, HCF control PWB. • 01G +24V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Tray 3 and 4 transport motor, PL 8.30 Item 7. • HCF control PWB, PL 7.20 Item 2. Y↓N→Check the gears and drive belt, PL 8.30 Item 8, PL 8.30 Item 9, GP 7. Perform the following: • Check the tray 3 and tray 4 transport rolls, PL 8.30 Item 18, GP 7. • If the fault occurs when feeding from tray 4. Go to RAP 08-104, 08-114 Tray 4 Misfeed RAP. • If the fault occurs when feeding from tray 3. Check the following, GP 7: – The takeaway roll assembly, PL 8.35 Item 2. – The transport roll assembly, PL 8.35 Item 11. – The transport roll bearing, PL 8.35 Item 3. – Go to RAP 08-103, 08-113 Tray 3 Misfeed RAP

Code: 08-115, 08-117

Description: Tray 5 Misfeed Entry RAP 08-115 The lead edge of the paper was late to the wait point sensor. 08-117 The lead edge of the paper failed to reach the feed sensor within the correct time after paper feed.
Remedy: Identify the speed of the machine, refer to SCP 7 Machine features. Perform one of the steps that follow: • If the speed of the machine is 35-55 ppm, go to 08-115A, 08-117A Tray 5 Misfeed RAP (35-55 ppm) • If the speed of the machine is 65-90 ppm, go to 08-115B, 08-117B Tray 5 Misfeed RAP (65-90 ppm).

Code: 08-115A, 08-117A

Description: Tray 5 Misfeed RAP (35-55 ppm)
Remedy: NOTE: The front door interlock must be cheated when checking +24V components. Enter dC330 code 08-105 tray 5 feed sensor, Q08-105. Press Start. Manually actuate the sensor. The display changes. Y↓N→Go to Flag 1. Check Q08-105. Refer to: • GP 11 How to Check a Sensor. • P/J505, Tray 5 control PWB • 01E +5V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Tray 5 feed sensor, PL 8.45 Item 6. • Tray 5 control PWB, PL 7.68 Item 8. Enter dC330 code 08-117 tray 5 feed motor, MOT08-117. Open the door. Press Start. The motor runs. Y↓N→Go to Flag 4. Check MOT08-117. Refer to: • GP 10 How to Check a motor. • P/J511, Tray 5 control PWB. • 01G +24V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Tray 5 feed motor, PL 8.40 Item 3. • Tray 5 control PWB, PL 7.68 Item 8. The feed shaft rotates. Y↓N→Check the drive gears between the motor and the feed shaft. Install new components as necessary: • Motor drive gear, PL 8.40 Item 5. • Gear 30T bearing, PL 8.40 Item 21. • Gear, PL 8.45 Item 14. The feed roll rotates Y↓N→Check the one way coupling, feed roll and clutch. Install new components as necessary: • One way coupling, PL 8.45 Item 4. • Clutch, PL 8.45 Item 13. • Feed roll, PL 8.45 Item 12. The nudger roll rotates Y↓N→Check the nudger roll and the one way gear. Check the drive belt between the feed roll and the nudger roll. Install new components as necessary: • One way gear, PL 8.45 Item 3. • Drive belt, PL 8.40 Item 7. • Nudger roll, PL 8.45 Item 10. The retard roll rotates Y↓N→Check the retard roll, retard clutch and clutch. Install new components as necessary: • Retard clutch, PL 8.47 Item 11. • Clutch, PL 8.47 Item 7. • Retard roll, PL 8.47 Item 2. Enter dC330 code 08-046 tray 5 transport motor, MOT08-046. Press Start. The motor runs. Y↓N→Go to Flag 3. Check MOT08-046. Refer to: • GP 10 How to Check a Motor. • P/J503, Tray 5 control PWB • 01G +24V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Tray 5 transport motor, PL 8.40 Item 2. • Tray 5 control PWB, PL 7.68 Item 8. Run the motor for 30 seconds. The motor runs at a constant speed, without slowing. Y↓N→Install a new tray 5 transport motor, PL 8.40 Item 2. The take away roller rotates. Y↓N→Check the drive belt and the one way pulley clutch for damage, GP 7. Check the belt tensioner. Install new components as necessary: • Drive belt, PL 8.40 Item 7. • One way pulley clutch, PL 8.47 Item 4. • Take away roller, PL 8.47 Item 5. Enter dC330 code 08-110 T5 wait point sensor, Q08-110. Press Start. NOTE: For trays 1 to 5 the input code 08-100 wait sensor is used to check the operation of the wait sensor. In addition tray 5 uses the input code 08-110 T5 wait point sensor, to check the paper present signal from the IOT PWB to the tray 5 control PWB. Open the left hand door and manually actuate the wait sensor. The display changes. Y↓N→Enter dC330 code 08-100 wait sensor, Q08-100. Press Start. Manually actuate the wait sensor. The display changes. Y↓N→Go to Flag 2. Check Q08-100. Refer to: • GP 11 How to Check a Sensor. • P/J5, IOT PWB. • 01D +3.3V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Wait sensor, PL 8.15 Item 3. • Perform OF7 IOT PWB Diagnostics RAP before a new IOT PWB is installed, PL 1.10 Item 2. Go to Flag 5. Manually actuate the wait sensor. Check for a signal change on the IOT PWB at P/J12 pin 10 and on the tray 5 control PWB at P/J512 pin 5. Check the wiring between the IOT PWB and the tray 5 control PWB. Install new components as necessary: • Tray 5 control PWB, PL 7.68 Item 8. • Perform OF7 IOT PWB Diagnostics RAP before a new IOT PWB is installed, PL 1.10 Item 2. Perform the steps that follow: • Clean the feed roll using a cloth dampened with water. • Install a new feed, nudger and retard roll, PL 8.45 Item 21.

Code: 08-115B, 08-117B

Description: Tray 5 Misfeed RAP (65-90 ppm)
Remedy: NOTE: The front door interlock must be cheated when checking +24V components. Enter dC330 code 08-105 tray 5 feed sensor, Q08-105. Press Start. Manually actuate the sensor. The display changes. Y↓N→Go to Flag 1. Check Q08-105. Refer to: • GP 11 How to Check a Sensor. • P/J505, Tray 5 control PWB • 01E +5V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Tray 5 feed sensor, PL 8.45 Item 6. • Tray 5 control PWB, PL 7.68 Item 8. Enter dC330 code 08-117 tray 5 feed motor, MOT08-117. Open the door. Press Start. The motor runs. Y↓N→Go to Flag 4. Check MOT08-117. Refer to: • GP 10 How to Check a motor. • P/J511, Tray 5 control PWB. • 01G +24V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Tray 5 feed motor, PL 8.40 Item 3. • Tray 5 control PWB, PL 7.68 Item 8. The feed shaft rotates. Y↓N→Check the drive gears between the motor and the feed shaft. Install new components as necessary: • Motor drive gear, PL 8.40 Item 5. • Gear 30T bearing, PL 8.40 Item 21. • Gear, PL 8.45 Item 14. The feed roll rotates Y↓N→Check the one way coupling, feed roll and clutch. Install new components as necessary: • One way coupling, PL 8.45 Item 4. • Clutch, PL 8.45 Item 13. • Feed roll, PL 8.45 Item 12. The nudger roll rotates Y↓N→Check the nudger roll and the one way gear. Check the drive belt between the feed roll and the nudger roll. Install new components as necessary: • One way gear, PL 8.45 Item 3. • Drive belt, PL 8.40 Item 7. • Nudger roll, PL 8.45 Item 10. The retard roll rotates Y↓N→Check the retard roll, retard clutch and clutch. Install new components as necessary: • Retard clutch, PL 8.47 Item 11. • Idler roll, PL 8.47 Item 7. • Retard roll, PL 8.47 Item 2. Enter dC330 code 08-046 tray 5 transport motor, MOT08-046. Press Start. The motor runs. Y↓N→Go to Flag 3. Check MOT08-046. Refer to: • GP 10 How to Check a Motor. • P/J503, Tray 5 control PWB • 01G +24V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Tray 5 transport motor, PL 8.40 Item 2. • Tray 5 control PWB, PL 7.68 Item 8. Run the motor for 30 seconds. The motor runs at a constant speed, without slowing. Y↓N→Install a new tray 5 transport motor, PL 8.40 Item 2. The take away roller rotates. Y↓N→Check the drive belt and the one way pulley clutch for damage, GP 7. Check the belt tensioner. Install new components as necessary: • Drive belt, PL 8.40 Item 7. • One way pulley clutch, PL 8.47 Item 4. • Take away roller, PL 8.47 Item 5. Enter dC330 code 08-110 T5 wait point sensor, Q08-110. Press Start. NOTE: For trays 1 to 5 the input code 08-100 wait sensor is used to check the operation of the wait sensor. In addition tray 5 uses the input code 08-110 T5 wait point sensor, to check the paper present signal from the IOT PWB to the tray 5 control PWB. Open the left hand door and manually actuate the wait sensor. The display changes. Y↓N→Enter dC330 code 08-100 wait sensor, Q08-100. Press Start. Manually actuate the wait sensor. The display changes. Y↓N→Go to Flag 2. Check Q08-100. Refer to: • GP 11 How to Check a Sensor. • P/J16, IOT PWB. • 01E +5V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Wait sensor, PL 7.30 Item 24. • Perform OF7 IOT PWB Diagnostics RAP before a new IOT PWB is installed, PL 1.10 Item 2. Go to Flag 5. Manually actuate the wait sensor. Check for a signal change on the IOT PWB at P/J12 pin 10 and on the Tray 5 control PWB at P/J512 pin 5. Check the wiring between the IOT PWB and the tray 5 control PWB. Install new components as necessary: • Tray 5 control PWB, PL 7.68 Item 8. • Perform OF7 IOT PWB Diagnostics RAP before a new IOT PWB is installed, PL 1.10 Item 2. Perform the steps that follow: • Clean the feed roll using a cloth dampened with water. • Install a new feed, nudger and retard roll, PL 8.45 Item 21.

Code: 08-131

Description: Lead Edge Late to Tray 3 Exit Sensor RAP (W/TAG 151) 08-103 The lead edge of the paper sheet fed from tray 3 reached the tray 3 feed sensor but did not reach the tray 3 exit sensor.
Remedy: NOTE: The front door interlock must be cheated when checking +24V components. Locate the tray 3 exit sensor, Q08-109.. Enter dC330 code 08-109 tray 3 exit sensor, Q08-109. Press Start. Manually actuate the sensor using white paper. The display changes. Y↓N→Go to Flag 1. Check Q08-109. Refer to: • GP 11 How to Check a Sensor. • P/J19, HCF control PWB. • 01E +5V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Tray 3 exit sensor, PL 8.32 Item 6. • HCF control PWB, PL 7.21 Item 2. CAUTION To prevent damage to the feed mechanism, the paper tray must be pulled out before MOT 08- 030 is run in diagnostics. Enter dC330 code 08-030 tray 3 feed motor, MOT08-030. Pull out the tray. Press Start. The motor runs. Y↓N→Go to Flag 3. Check MOT08-030. Refer to: • GP 10 How to Check a Motor. • P/J4, HCF control PWB. • 01G +24V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Tray 3 feed motor, PL 8.32 Item 11. • HCF control PWB, PL 7.21 Item 2. Locate the tray 3 feed clutch, CL08-033.. Enter dC330 code 08-030 tray 3 feed motor, MOT08-030, stack the code 08-033 tray 3 feed clutch, CL08-033. Pull out tray 3 and observe the tray 3 feed and nudger rolls. Press Start. The rolls rotate. Y↓N→Go to Flag 3. Check CL08-033. Refer to: • GP 12 How to Check a Solenoid or Clutch. • P/J4, HCF control PWB. • 01G +24V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Tray 3 paper feed assembly, PL 8.32 Item 1. • HCF control PWB, PL 7.21 Item 2. Perform the following: • Clean the feed roll, nudger roll and retard roll using a cloth dampened with water. • Check the feed roll, nudger roll and retard roll for wear. If necessary install a new feed roll kit (W/TAG 151), PL 31.11.

Code: 08-132

Description: Tray 3 Paper Feed Jam RAP (W/TAG 151) 08-132 The lead edge of the paper was late to the HCF exit sensor when feeding from tray 3.
Remedy: NOTE: The front door interlock must be cheated when checking +24V components. Enter dC330 code 08-108 HCF exit sensor, Q08-104. Press Start. Manually actuate the HCF exit sensor. The display changes. Y↓N→Go to Flag 1. Check Q08-108. Refer to: • GP 11 How to Check a Sensor. • P/J3, HCF control PWB. • 01E +5V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • HCF exit sensor, PL 8.33 Item 3. • HCF control PWB, PL 7.21 Item 2. Enter dC330 code 08-045 HCF transport motor, MOT08-045. Press Start. The motor runs. Y↓N→Go to Flag 2. Check MOT08-045. Refer to: • GP 10 How to Check a Motor. • P/J6, HCF control PWB. • 01G +24V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • HCF transport motor, PL 8.32 Item 10. • HCF control PWB, PL 7.21 Item 2. The transport rolls rotate. Y↓N→Check the following: •, drive belt, PL 8.36 Item 6. •, drive coupling, PL 8.36 Item 7. •, idler roll assembly, PL 8.36 Item 8. • Tray 3 and 4 transport roll, PL 8.32 Item 4 Perform the 08-103, 08-113 Tray 3 Misfeed RAP.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie