Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Xerox WorkCentre 5745 — Trang 7/27

Code: 07-304B

Description: Tray 4 Open During Run RAP (W/TAG 151)
Remedy: Enter dC330 code 07-304 tray 4 home sensor, Q07-304. Press Start. Open and fully close the tray. The display changes. Y↓N→Go to Flag 1. Check Q07-304. Refer to: • GP 11 How to Check a Sensor. • P/J1 HCF control PWB. • 01B 0V Distribution RAP. Install new components as necessary: • Tray 4 home sensor, PL 7.21 Item 4. • HCF control PWB, PL 7.21 Item 2. Check the sensor holder, PL 7.21 Item 3. If the problem continues, install new components as necessary: • Tray 4 home sensor, PL 7.21 Item 4. • HCF control PWB, PL 7.21 Item 2.

Code: 07-306

Description: Tray 5 Door Open During Run RAP 07-306 Tray 5 door open during run when the paper is fed from tray 5.
Remedy: Enter dC330 code 07-306 tray 5 door switch, S07-306 Press Start. Open and fully close the door The display changes. Y↓N→Go to Flag 1. Check S07-306. Refer to: • GP 13 How to Check a Switch. • 01E +5V Distribution RAP • P/J507, Tray 5 control PWB. • 01B 0V Distribution RAP. Install new components as necessary: • Tray 5 door switch, PL 7.60 Item 6. • Tray 5 control PWB, PL 7.68 Item 8. If the problem continues, install new components as necessary: • Tray 5 door switch, PL 7.60 Item 6 • Tray 5 control PWB, PL 7.68 Item 8.

Code: 07-353

Description: Tray 1 Elevator Lift Failure RAP 07-353 Tray 1 stack height sensor did not actuate within the correct time after the feed / elevator motor turned on.
Remedy: Enter dC330 code 07-336 tray 1 stack height sensor, Q07-336. Press Start. Pull out tray 1 and push fully home. The display changes Y↓N→Go to Flag 1. Check Q07-383. Refer to: • GP 11 How to Check a Sensor. • P/J274, Tray 1 and 2 control PWB • 01E +5V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Tray 1 stack height sensor, PL 8.26 Item 8. • Tray 1 and 2 control PWB, PL 7.10 Item 2. CAUTION To prevent damage to the elevator and paper feed mechanism, the paper tray must be pulled out before MOT07-010 is run in diagnostics. Enter dC330 code 07-010 tray 1 feed / elevator motor, MOT07-010. Pull out tray 1. Press Start. The motor runs Y↓N→Go to Flag 2. Check MOT07-010. Refer to: • GP 10 How to Check a Motor. • P/J274, Tray 1 and 2 control PWB. • 01G +24V Distribution RAP. • 01B 0V Distribution RAP Install new components as necessary: • Tray 1 Feed / elevator motor, PL 8.26 Item 8. • Tray 1 and 2 control PWB, PL 7.10 Item 2. Perform the following: • Check the feeder / elevator motor drive gears. • Check the tray 1 stack height mechanism on the feeder assembly, If the fault still occurs then go to 07A Tray 1 and Tray 2 False Paper Level RAP.

Code: 07-354

Description: Tray 2 Elevator Lift Failure RAP 07-354 Tray 2 stack height sensor did not actuate within the correct time after the feed / elevator motor turned on.
Remedy: Enter dC330 code 07-337 tray 2 stack height sensor, Q07-337. Press Start. Pull out tray 1 and push fully home. The display changes Y↓N→Go to Flag 1. Check Q07-337. Refer to: • GP 11 How to Check a Sensor. • P/J275, Tray 1 and 2 control PWB. • 01E +5V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Tray 2 stack height sensor, PL 8.26 Item 8. • Tray 1 and 2 control PWB, PL 7.10 Item 2. CAUTION To prevent damage to the elevator and paper feed mechanism, the paper tray must be pulled out before MOT07-020 is run in diagnostics. Enter dC330 code 07-020 tray 1 feed / elevator motor, MOT07-020. Pull out tray 1. Press Start. The motor runs Y↓N→Go to Flag 2. Check MOT07-020. Refer to: • GP 10 How to Check a Motor. • P/J275, Tray 1 and 2 control PWB. • 01G +24V Distribution RAP. • 01B 0V Distribution RAP Install new components as necessary: • Tray 2 Feed / elevator motor, PL 8.26 Item 6. • Tray 1 and 2 control PWB, PL 7.10 Item 2. Perform the following: • Check the feeder / elevator motor drive gears. • Check the tray 2 stack height mechanism on the feeder assembly, If the fault still occurs then go to 07A Tray 1 and Tray 2 False Paper Level RAP.

Code: 07-355

Description: Tray 3 Elevator Lift Failure Entry RAP 07-355 Tray 3 stack height sensor does not actuate within the correct time after the elevator motor turned on.
Remedy: Go to the relevant procedure: • (W/O TAG 151) go to the 07-355A Tray 3 Elevator Lift Failure RAP (W/O TAG 151). • (W/TAG 151g) go to the 07-355B Tray 3 Elevator Lift Failure RAP (W/TAG 151).

Code: 07-355A

Description: Tray 3 Elevator Lift Failure RAP (W/O TAG 151)
Remedy: Enter dC330 code 07-303 tray 3 home switch, S07-303. Press Start. Pull out the tray and push back in. The display changes. Y↓N→Go to Flag 1. Check S07-303. Refer to: • GP 13 How to Check a Switch. • P/J392, HCF control PWB. • 01E +5V Distribution RAP. • 01B 0V Distribution RAP Install new components as necessary: • Tray 3 home switch, PL 7.20 Item 4. • HCF control PWB, PL 7.20 Item 2. Enter dC330 code 07-383 tray 3 stack height sensor, Q07-383. Press Start. Pull out tray 3 and manually activate the stack height sensor on the paper feed assembly. The display changes Y↓N→Go to Flag 2. Check Q07-383. Refer to: • GP 11 How to Check a Sensor. • P/J392, HCF control PWB. • 01E +5V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Tray 3 stack height sensor, PL 8.30 Item 21 • HCF control PWB, PL 7.20 Item 2. Disconnect P/J396 on the HCF control PWB, Flag 3. Connect a service meter between pin 1 and pin 3 on the wiring side of the connector. Continuity is measured when the switch is deactivated and open circuit is measured when the switch is actuated. Y↓N→Go to Flag 3. Check S07-393. Refer to: • GP 13 How to Check a Switch. • P/J396, HCF control PWB. • 01G +24V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Tray 3 paper feeder, PL 8.30 Item 2. • HCF control PWB, PL 7.20 Item 2. CAUTION To prevent damage to the elevator and paper feed mechanism, the paper tray must be pulled out before MOT07-030 is run in diagnostics. Enter dC330 code 07-030 tray 3 elevator motor, MOT07-030. Pull out tray 3. Press Start. The motor runs Y↓N→Go to Flag 4. Check MOT07-030. Refer to: • GP 10 How to Check a Motor. • P/J395, HCF control PWB. • 01G +24V Distribution RAP. • 01B 0V Distribution RAP Install new components as necessary: • Tray 3 elevator motor, PL 7.20 Item 1. • HCF control PWB, PL 7.20 Item 2. Perform the following: • Check elevator cables, PL 7.15 Item 4, PL 7.15 Item 6, PL 7.15 Item 7. • Check elevator motor drive coupling, PL 7.20 Item 1. • Check tray elevator drive gears and drive coupling, PL 7.15. • Check the tray 3 empty sensor actuator, PL 8.30 Item 1. If the fault still occurs go to 07E Tray 3 or Tray 4 Out of Paper RAP.

Code: 07-355B

Description: Tray 3 Elevator Lift Failure RAP (W/TAG 151)
Remedy: Enter dC330 code 07-303 tray 3 home sensor, Q07-303. Press Start. Pull out the tray and push back in. The display changes. Y↓N→Go to Flag 1. Check S07-303. Refer to: • GP 11 How to Check a Sensor. • P/J1, HCF control PWB. • 01E +5V Distribution RAP. • 01B 0V Distribution RAP Install new components as necessary: • Tray 3 home sensor, PL 7.21 Item 4. • HCF control PWB, PL 7.21 Item 2. Enter dC330 code 07-383 tray 3 stack height sensor, Q07-383. Press Start. Pull out tray 3 and manually activate the stack height sensor on the paper feed assembly. The display changes Y↓N→Go to Flag 2. Check Q07-383. Refer to: • GP 11 How to Check a Sensor. • P/J1, HCF control PWB. • 01E +5V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Tray 3 stack height sensor, PL 8.32 Item 7. • HCF control PWB, PL 7.21 Item 2. Disconnect P/J10 on the HCF control PWB, Flag 3. Connect a service meter between pin 1 and pin 2 on the wiring side of the connector. Continuity is measured when the stack limit switch is deactuated and open circuit is measured when the switch is actuated. Y↓N→Go to Flag 3. Check the stack limit switch. Refer to: • GP 13 How to Check a Switch. • P/J10, HCF control PWB. • 01G +24V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Tray 3 over elevate switch, PL 8.32 Item 9. • HCF control PWB, PL 7.21 Item 2. CAUTION To prevent damage to the elevator and paper feed mechanism, the paper tray must be pulled out before MOT07-030 is run in diagnostics. Re-connect P/J10. Enter dC330 code 07-030 tray 3 elevator motor, MOT07-030. Pull out tray 3. Press Start. The motor runs Y↓N→Go to Flag 4. Check MOT07-030. Refer to: • GP 10 How to Check a Motor. • P/J13, HCF control PWB. • 01G +24V Distribution RAP. • 01B 0V Distribution RAP Install new components as necessary: • Tray 3 elevator motor, PL 7.21 Item 1. • HCF control PWB, PL 7.21 Item 2. Perform the following: • Check the elevator cables, PL 7.18 Item 4, PL 7.18 Item 6, PL 7.18 Item 8. • Check the elevator drives gear coupling, PL 7.19 Item 10. If the fault still occurs go to 07E Tray 3 or Tray 4 Out of Paper RAP.

Code: 07-360

Description: Tray 4 Elevator Lift Failure Entry RAP 07-360 Tray 4 stack height sensor does not actuate within 7 seconds after the elevator motor is turned on.
Remedy: Go to the relevant procedure: • (W/O TAG 151) go to the 07-360A Tray 4 Elevator Lift Failure RAP (W/O TAG 151). • (W/TAG 151) go to the 07-360B Tray 4 Elevator Lift Failure RAP (W/TAG 151).
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie