Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi E4-3, E4-5 — Xerox Phaser 5550

Code: E4-3, E4-5

Description: Jam at E - E4-3 Exit 2 Area Jam Paper did not pass the Exit 2 Exit Sensor located behind Door E on time. • Jam at E - E4-3 Exit 2 Area Jam • Jam at A - E4-5 Exit 2 Area Jam
Causes: • Exit 2 Exit Sensor • Exit 2 Motor • Exit 2 OCT Roller • Exit 2 FU Roller • Exit 2 Inv Roller • Exit PWB • Engine Control Board • LVPS
Remedy: 1 Check paper position at Door E. Is paper touching the Exit 2 Sensor? Remove the paper. Go to Step 2. 2 Check the FU Roller. Is the FU Roller worn or contaminated with paper dust? Clean or replace the FU Roller. Go to Step 3. 3 Check the drive transmission. Does the FU Roller and gears rotate smoothly? Go to Step 4. Restore proper operation. 4 Check the Inv Roller. Is the INV Roller worn or contaminated with paper dust? Clean or replace the INV Roller. Go to Step 5. 5 Check the drive transmission. Does the INV Roller and gears rotate smoothly? Go to Step 6. Restore proper operation. 6 Check the OCT Roller. Is the OCT Roller worn or contaminated with paper dust? Clean or replace the OCT Roller. Go to Step 7. 7 Check the drive transmission. Does the OCT Roller and gears rotate smoothly? For E4-5: Go to Step 8. For E4-3: Go to Step 9. Restore proper operation. 8 For E4-5 Only: Test Exit 2 Gate Solenoid. Run the Service Diagnostics Exit 2 Gate Solenoid test. Does the Solenoid operate the Gate? Go to Step 9. Go to Step 10. 9 Test the Exit 2 Sensor. 1. Open Door E. 2. Run the Service Diagnostics Exit Sensor test. Does the sensor change state? For E4-5: Go to Step 10. For E4-3: Go to Step 12. Go to Step12. 10 For E4-5 Only: Check Exit 2 Solenoid. Check continuity on each wire between P/ J209 to P/J433. Is there continuity on each wire between P/ J209 to P/J433. Go to Step 11. Repair the wiring. 11 For E4-5 Only: Check for +24 V to the Exit 2 Gate Solenoid. Is there +24 V across P/J433-11 (+) <=> ground? Replace the Exit 2 Gate Solenoid. Replace the Exit PWB. 12 Check the Exit Sensor connection. Are P/J112, P/J606B, and P/J434 connected? Go to Step 13. Connect the sensor. 13 Check continuity between the Exit Sensor and Exit PWB. Is there continuity on each wire between P/ J112 <=> P/J434? Go to Step 14. Repair the wiring. 14 Check for +5 V at the Exit Sensor. Is there +5 V across the sensor connector’s P/J112-3 <=> ground? Replace the Exit 2 Sensor. Go to Step 15. 15 Check the connection between the Exit PWB and Engine Control Board. Are P/J431 and P/J421 connected? Go to Step 16. Connect P/J431 and P/J421. 16 Check continuity between the Exit PWB and the Engine Control Board. Is there continuity on each wire between P/ J431 <=> P/J421? Go to Step 17. Repair the wiring. 17 Check the connection between the Exit PWB and the LVPS. Are P/J430 and P/J526 connected? Go to Step 18. Connect P/J430 and P/J526. 18 Check continuity between the Exit PWB and the LVPS. Is there continuity on each wire between P/ J430 <=> P/J526? Go to Step 19. Repair the wiring. 19 Check for +24 V to the Exit PWB. Is there +24 V across P/J430-1 (+) <=> ground? Replace the Exit PWB. Replace the LVPS. 20 Test the Exit 2 Motor operation. Run the Service Diagnostics Exit 2 Output Motor tests. Does the Exit 2 Motor operate properly? Replace the Engine Control Board. Go to Step 21. 21 Check the Exit 2 Motor connection. Are P/J208, P/J606A and P/J433 connected? Go to Step 22. Connect P/J208, P/J606A and P/ J433. 22 Check continuity between the Exit 2 Motor and Exit PWB. Is there continuity on each wire between P/ J208 <=> P/J433? Go to Step 23. Repair the wiring. 23 Check for +24 V to the Exit 2 Motor. Is there +24 V across P208-5 (+) <=> ground? Replace the Exit 2 Motor. Go to Step 24. 24 Check the connection between the Exit PWB and Engine Control Board. Are P/J431 and P/J421 connected? Go to Step 25. Connect P/J431 and P/J421. 25 Check continuity between the Exit PWB and Engine Control Board. Is there continuity on each wire between P/ J431 <=> P/J421? Go to Step 26. Repair the wiring. 26 Check the connection between the Exit PWB and the LVPS. Are P/J430 and P/J526 connected? Go to Step 27. Connect P/J430 and P/J526. 27 Check continuity between the Exit PWB and the LVPS. Is there continuity on each wire between P/ J430 <=> P/J526? Go to Step 28. Repair the wiring. 28 Check for +24 V to the Exit PWB. Is there +24 V across P/J430-1 (+) <=> ground? Replace the Exit PWB. Replace the LVPS.

← Xem tất cả mã lỗi Xerox Phaser 5550

Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie