Code: H3-1, H3-2
Description: Exit Unit Failure - H3-n Offset Error Failure to establish Offset Home Position on Exit1 (H3-1) or Exit 2 (H3-2).
Causes: • OCT Position Sensor • Offset Motor • Exit PWB • LVPS • Engine Control Board
Remedy: 1 Test the affected OCT Position Sensor. Run the Service Diagnostics Exit 1 or 2 Offset Home Position Sensor test. Does the sensor state change? Go to Step 10. Go to Step 2. 2 Check the sensor connection. Is P/J117 (Exit 1) or P/J111 (Exit 2) connected? Go to Step 3. Connect the sensor. 3 Check continuity between the affected OCT Position Sensor and the Exit PWB P/J111 <=> P/J434 and SJ1 (Exit2) P/J117 <=> P/ J423 (Exit 1). Go to Step 4. Repair the wiring. 4 Check for +5 V to the OCT Position Sensor. Is there +5 V across P/J434-1 (Exit 2) or P/ J432-1 (Exit 1) (+) <=> ground? Replace the affected OCT Position Sensor. Go to Step 5. 5 Check the connection between the Exit PWB and the Engine Control Board. Are P/J431 and P/J421 connected? Go to Step 6. Connect P/J431 and P/J421. If problem persists, go to Step 6. 6 Check continuity between the Exit PWB and the Engine Control Board. 1. Disconnect P/J431 and P/J421. 2. Check for continuity at the following: • P/J431-1 <=> P/J421-8 • P/J431-2 <=> P/J421-7 • P/J431-3 <=> P/J421-6 • P/J431-4 <=> P/J421-5 • P/J431-5 <=> P/J421-4 • P/J431-6 <=> P/J421-3 • P/J431-7 <=> P/J421-2 • P/J431-8 <=> P/J421-1 Are these conductive? Go to Step 7. Repair the wiring. 7 Check the connection between the Exit PWB and the LVPS. Are P/J430 and P/J526 connected? Go to Step 8. Connect P/J430 and P/J526. If problem persists, go to Step 8. 8 Check continuity between the Exit PWB and the LVPS. 1. Disconnect P/J430 and P/J526. 2. Check for continuity at the following: • P/J430-3 <=> P/J526-6 • P/J430-4 <=> P/J526-5 • P/J430-1 <=> P/J526-8 • P/J430-2 <=> P/J526-7 Are these conductive? Go to Step 9. Repair the wiring. 9 Check for +24 V to the Exit PWB. Is there +24 V across P/J430-1 (+) <=> ground? Replace the Exit PWB. Replace the LVPS. 10 Test the Offset Motor. Run the Service Diagnostics Offset Output Motor tests for the appropriate Exit. Does the Offset Motor operate properly? Replace the Exit PWB. If problem persists, replace the Engine Control Board. Go to Step 11. 11 Check the affected Offset Motor connection. Exit 1 P/J432 <=> J206 or Exit 2 P/J433 <=> J207. Is the motor connected? Go to Step 12. Connect the motor. If problem persists go to Step 12. 12 Check continuity between the affected Offset Motor and Exit PWB. For Exit 1: 1. Disconnect P/J432 and J206. 2. Check for continuity at the following: • P/J432-7 <=> J206-1 • P/J432-8 <=> J206-2 • P/J432-9 <=> J206-3 • P/J432-10 <=> J206-4 • P/J432-11 <=> J206-5 For Exit 2: 1. Disconnect P/J433 and J207. 2. Check for continuity at the following: • P/J433-1 <=> J207-1 • P/J433-2 <=> J207-2 • P/J433-3 <=> J207-3 • P/J433-4 <=> J207-4 • P/J433-5 <=> J207-5 Is there continuity on each wire? Go to Step 13. Repair the wiring. 13 Check for +24 V to the affected Offset Motor. Is there +24 V across (Exit 2) P/J433-1 or (Exit 1) P/J432-7(+) <=> ground? Replace the Offset Motor. Replace the Exit PWB.