Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi H5-11 — Xerox Phaser 5550

Code: H5-11

Description: Stacker Lower Tray Failure - H5-11 Low Tray Fail The Lower Tray No Paper Sensor is not turned Off or On within the specified time following the Stacker Tray beginning to move.
Causes: • Lower Tray No Paper Sensor • Upper Limit Actuator • Finisher Main PWB • Main Sensor Harness • Elevator Motor • Engine Control Board
Remedy: 1 Check the Stacker Lower Tray vertical transport and belts for obstacles and deformation. Are there obstacles or belt wear in the vertical transport mechanism? Remove obstacles/ replace deformed part. Go to Step 2. 2 Check the Actuator installation. Does the Actuator enter the Upper Limit sensor sensing area? Go to Step 3. Repair the Actuator. 3 Test the Lower Tray No Paper Sensor. Run the Service Diagnostics Lower Tray No Paper Sensor test. Does the sensor state change when the sensor is blocked? Go to Step 9. Go to Step 4. 4 Check the Lower Tray No Paper Sensor Harness connection. Are P/J8326 and P/J8302B connected? Go to Step 6. Connect and go to Step 5. 5 Print a Test Print. Does the error still occur? Go to Step 6. Problem solved. 6 Check the Lower Tray No Paper Sensor Harness continuity. 1. Disconnect P/J8326 on the Lower Tray No Paper Sensor Harness, and P/ J8302B on the Finisher Main PWB. 2. Check for continuity at the following: • P/J8326-3 <=> P/J8302B-15 • P/J8326-2 <=> P/J8302B-16 • P/J8326-1 <=> P/J8302B-17 Are these conductive? Go to Step 7. Repair the Lower Tray No Paper Sensor Harness. If problem persists, go to Step 7 7 Check for +5 V to the Lower Tray No Paper Sensor. Is there +5 V across J8302B-17 <=> J8302B-15 on the Finisher Main PWB? Go to Step 8. Replace the Finisher Main PWB. 8 Check Stacker Lower Tray No Paper Sensor. Does the voltage across P8302B-16 <=> P8302B-15 on the Finisher Main PWB change when the sensor is blocked? Replace the Finisher Main PWB. Replace the Lower Tray No Paper Sensor. 9 Test the Elevator Motor. Run the Service Diagnostics Stacker Motor Up and Down tests alternately. Does the Elevator Motor operate? Replace the Finisher Main PWB. Go to Step 10. 10 Check the Elevator Motor connection. Is P/J8305 connected to the Finisher Main PWB? Go to Step 12. Connect and go to Step 11. 11 Print a Test Print. Does the error still occur? Go to Step 12. Problem solved. 12 Replace the Elevator Motor. Print a Test Print. Does the error still occur? Go to Step 13. Problem solved. 13 Replace the Finisher Main PWB. Does the error still occur? Replace the Engine Control Board. Problem solved.

← Xem tất cả mã lỗi Xerox Phaser 5550

Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie