Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi H5-83, H5-84 — Xerox Phaser 5550

Code: H5-83, H5-84

Description: Stacker Lower Tray Failure - H5-8n Set Clamp Sensor The Set Clamp Home Sensor does not change state within the time interval specified following the start or stop of the Set Clamp. When printing jobs to the Stacker Lower Tray the failure occurs when paper is entering the Compiler Tray and the eject pinch roller assembly completes a clamp cycle. The printer will declare the Stacker Lower Tray Failure and continue to run in a degraded mode sending pages remaining in the paper path to the Stacker Upper Tray then the remainder of the job to the Standard Output Tray. • Stacker Lower Tray Failure - H5-83 Set Clamp SNR ON • Stacker Lower Tray Failure - H5-84 Set Clamp SNR OFF
Causes: • Set Clamp Home Sensor • Main Sensor Harness • Finisher Main PWB • Eject Bracket Assembly • Main Drive Harness • Set Clamp Clutch
Remedy: 1 Check the Eject Clamp operation. Rotate the Eject Clamp Motor. Does the Eject Clamp move smoothly? Go to Step 2. Correct the installation. 2 Test the Set Clamp Home Sensor. Run the Service Diagnostics Set Clamp Home Sensor test. Does the sensor change state? Go to Step 8. Go to Step 3. 3 Check the Set Clamp Home Sensor Harness connection. Are P/J8325 and P/J8302B connected? Go to Step 5. Connect and go to Step 4. 4 Print a Test Print. Does the error still occur? Go to Step 5. Problem solved. 5 Check the Set Clamp Home Sensor Harness continuity. 1. Disconnect P/J8325 and P/J8302B. 2. Check for continuity at the following: • P/J8325-3 <=> P/J8302B-4 • P/J8325-2 <=> P/J8302B-9 • P/J8325-1 <=> P/J8302B-11 Are these conductive? Go to Step 6. Repair the Set Clamp Home Sensor Harness. 6 Check for +5 V to the Set Clamp Home Sensor. Is there +5 V across J8302B-11 <=> J8302B-9 on the Finisher Main PWB for H5- 83? Is there +5 V across J8302B-4 <=> J8302B- 9 on the Finisher Main PWB for H5-84? Go to Step 7. Replace the Finisher Main PWB. 7 Check the Set Clamp Home Sensor signal. Does the voltage across P8302B-11<=> P8302B-9 on the Finisher Main PWB change when the sensor is blocked? Replace the Finisher Main PWB. Replace the Set Clamp Home Sensor. 8 Test the Eject Motor. Run the Service Diagnostics Low Speed Forward and Reverse Eject Motor tests. Does the Eject Motor rotate normally? Go to Step 15. Go to Step 9. 9 Check Eject Motor Harness connections. Are P/J8336 and P/J8304 connected? Go to Step 11. Connect and go to Step 10. 10 Print a Test Print. Does the error still occur? Go to Step 11. Problem solved. 11 Check Eject Motor Harness continuity. 1. Disconnect P/J8336 and P/J8304. 2. Check for continuity at the following: • P/J8336-1 <=> P/J8304-15 • P/J8336-2 <=> P/J8304-12 • P/J8336-3 <=> P/J8304-17 • P/J8336-4 <=> P/J8304-19 • P/J8336-5 <=> P/J8304-14 • P/J8336-6 <=> P/J8304-21 Are these conductive? Go to Step 12. Repair the Eject Motor Harness. 12 Check Eject Motor resistance. Is there resistance across P8336-2/5(COM) and P8336-1/3/4/6? Go to Step 13. Replace the Eject Bracket Assembly. 13 Check for +24 V to the Eject Motor. Is there +24 V across J8304-12 <=> ground, and J8304-14 <=> ground on the Finisher Main PWB? Go to Step 14. Replace the Finisher Main PWB. 14 Replace the Eject Clamp Motor. Print a Test Print. Does the error still occur? Replace the Finisher Main PWB. Problem solved. 15 Test the Set Clamp Clutch (Clutch Z34). Run the Service Diagnostics Set Clamp Clutch test. Does the Set Clamp Clutch operate? Replace the Finisher Main PWB. Go to Step 16. 16 Check the Set Clamp Clutch Harness connection. Are P/J8338B and P/J8304 connected? Go to Step 18. Connect and go to Step 17. 17 Print a test Print. Does the error still occur? Go to Step 18. Problem solved. 18 Check Set Clamp Clutch Harness continuity. 1. Disconnect P/J8338B and P/J8304. 2. Check for continuity at the following: • J8338B-1 <=> P/J8304-20 • J8338B-2 <=> P/J8304-22 Go to Step 19. Repair the Set Clamp Clutch Harness. 19 Check for +24 V to the Set Clamp Clutch. Is there +24 V across J8304-22 <=> ground on the Finisher Main PWB? Go to Step 20. Replace the Finisher Main PWB. 20 Replace the Set Clamp Clutch. Print a Test Print. Does the error still occur? Replace the Finisher Main PWB. Problem solved.

← Xem tất cả mã lỗi Xerox Phaser 5550

Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie