Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi H5-86 — Xerox Phaser 5550

Code: H5-86

Description: Stacker Lower Tray Failure - H5-86 Side Regi Sensor OFF Either or both Side Registration Sensors do not transition within the time interval specified (500 ms) following activation of the Punch Move Motor or the state changes to On after the Punch Move Motor stops.
Causes: • Punch Move Motor • Punch Drive Harness • Finisher Main PWB • Engine Control Board • Side Registration Sensors • Punch Sensor Harness • Punch Unit Harness
Remedy: 1 Check the Punch operation. Move the Punch Unit in and out. Does the punch move smoothly? Go to Step 2. Correct the installation. 2 Test the Punch Move Motor. Run the Service Diagnostics Front and Rear Punch Move Motor tests. Does the Punch Move Motor rotate and the Punch frame move? Go to Step 8. Go t o Step 3. 3 Check Punch Move Motor Harness connections. Are P/J8344 and P/J8306 connected? Go to Step 5. Connect and go to Step 4. 4 Print a Test Print. Does the error still occur? Go to Step 5. Problem solved. 5 Check Punch Move Motor Harness continuity. 1. Disconnect P/J8344 and P/J8306. 2. Check for continuity at the following: • P/J8344-1 <=> P/J8306-7 • P/J8344-2 <=> P/J8306-3 • P/J8344-3 <=> P/J8306-6 • P/J8344-4 <=> P/J8306-5 • P/J8344-5 <=> P/J8306-2 • P/J8344-6 <=> P/J8306-1 Are these conductive? Go to Step 6. Repair the Punch Move Motor Harness. 6 Replace the Bracket Assy-Motor, Punch. Print a Test Print. Does the error still occur? Go to Step 7. Problem solved. 7 Replace the Finisher Main PWB. Does the error still occur? Replace the Finisher Main PWB. Problem solved. 8 Test the Side Regi Sensor 1 and 2. Run the Service Diagnostics Side Registration Sensor 1 test. Does the state change when each sensor is blocked? Replace the Finisher Main PWB. Go to Step 9. 9 Check the harness connections. Are P/J8307, P/J8333 and P/J8350 (for Side Regi Sensor 1), and P/J8351 (for Side Regi Sensor 2) connected? Go to Step 12. Connect and go to Step 10. 10 Print a Test Print. Does the error still occur? Go to Step 11. Problem solved. 11 Check Main Punch Sensor continuity Disconnect P/J8307 and P/J8333. Is there continuity on each wire between J8307 <=> J8333? Go to Step 12. Repair the Main Punch Sensor Harness. 12 Check Side Regi Sensor continuity. 1. Disconnect P/J8333, P/J8350 (Side Regi Sensor 1), and P/J8351 (Side Regi Sensor 2). 2. Check for continuity at the following: • P/J8333-13 <=> P/J8350-3 • P8333-14 <=> P/J8350-2 • P8333-15 <=> P/J8350-1 • P8333-16 <=>P/J8351-3 • P8333-17 <=> P/J8351-2 • P8333-18 <=> P/J8351-1 Are these conductive? Go to Step 13. Repair the Punch Unit Harness. 13 Check for +5 V at Side Regi Sensor 1. Is there +5 V between P/J8307-A10 <=> P/ J8307-A12? Go to Step 15. Go to Step 17. 14 Check for +5 V at Side Regi Sensor 2. Is there +5 V between P/J8307-A7 <=> P/ J8307-A9? Go to Step 16. Go to Step 17. 15 Replace the Side Registration Sensor 1. Does P/J8307-A11 change from 0 to 5V when the sensor is blocked? Complete. Go to Step 17. 16 Replace the Side Registration Sensor 2. Does P/J8307-A8 change from 0 to 5V when the sensor is blocked. Complete. Go to Step 17. 17 Replace the Finisher Main PWB. Does the error still occur? Replace the Engine Control Board. Problem solved.

← Xem tất cả mã lỗi Xerox Phaser 5550

Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie