Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi H5-95, H5-96 — Xerox Phaser 5550

Code: H5-95, H5-96

Description: Stapler Failure - H5-9n Move Sensor The Staple Move Position Sensor does not change state in the specified time interval after the Stapler Head starts moving toward or reaching the staple position. This error also occurs if the Stapler Move Position Sensor is turned OFF again after being ON and the Stapler Head is stopped. • Stapling Failure - H5-95 Move SNR ON • Stapling Failure - H5-96 Move SNR OFF
Causes: • Stapler Lower Carriage • Move Home Position Sensor • Stapler Harness • Finisher Main PWB
Remedy: 1 Check Staple Head motion. Slide the Staple Head across the rails. Does the Staple Head move smoothly? Go to Step 2. Remove obstacles or repair motion. 2 Test the Staple Move Motor. Run the Service Diagnostics Staple Move Motor mid speed Front and Rear tests. Does the Staple Head Jog? Go to Step 7. Go to Step 3. 3 Check the Staple Move Motor Harness connections. Are P/J8358 and P/J8308 connected? Go to Step 5. Connect and go to Step 4. 4 Staple a Test Print. Does the error still occur? Go to Step 5. Problem solved. 5 Check Staple Move Motor Harness continuity. 1. Disconnect P/J8358 and P/J8308. 2. Check for continuity at the following: • P/J8358-1 <=> P/J8308-3 • P/J8358-2 <=> P/J8308-6 • P/J8358-3 <=> P/J8308-5 • P/J8358-4 <=> P/J8308-1 • P/J8358-5 <=> P/J8308-4 • P/J8358-6 <=> P/J8308-2 Are these conductive? Go to Step 6. Repair the Staple Move Motor Harness. 6 Replace the Stapler Lower Carriage. Staple a Test Print. Does the error still occur? Replace the Finisher Main PWB. Problem solved. 7 Test the Staple Move Position Sensor. Run the Service Diagnostics Staple Move Position Sensor test. Does the sensor state change? Replace the Finisher Main PWB. Go to Step 8. 8 Check the Staple Move Position Sensor Harness connections. Are P/J8354 and P/J8308 connected? Go to Step 10. Connect and go to Step 9. 9 Staple a Test Print. Does the error still occur? Go to Step 10. Problem solved. 10 Check Staple Move Position Sensor Harness continuity. 1. Disconnect P/J8354 and P/J8308. 2. Check for continuity at the following: • P/J8354-1 <=> P/J8308-18 • P/J8354-2 <=> P/J8308-17 • P/J8354-3 <=> P/J8308-16 Are these conductive? Go to Step 11. Repair the Staple Move Position Sensor Harness. 11 Check for +5 V to the Stapler Move Position Sensor. Is there +5 V across J8308-18 <=> J8308-16 on the Finisher Main PWB? Go to Step 12. Replace the Finisher Main PWB. 12 Check the Stapler Move Home Position Sensor signal. Does the voltage across J8308-17 <=> J8308-16 on the Finisher Main PWB change when the sensor is blocked by moving the Stapler Head. Replace the Finisher Main PWB. Replace the Staple Move Position Sensor.

← Xem tất cả mã lỗi Xerox Phaser 5550

Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie