Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi 024-959 — Xerox Phaser 6280

Code: 024-959

Description: Load Tray 2 (No Suitable Paper) The type or size of paper mismatched or Tray 2 is empty.
Causes: • Tray 2, PL2.1.24 • Feeder Assy., PL3.2.1 • Tray 2 No Paper Sensor, PL3.2.30 • Registration Sensor Harness, PL3.2.37 • No Paper Actuator, PL3.2.49 • MCU Board, PL9.1.20 • Right Side Harness, PL10.1.15
Remedy: 1 1. Check the paper size. 2. Does the paper size meet specifications? Go to step 2. Replace the paper with the correct specifications. 2 1. Check the paper size setting. 2. Does the paper match with the settings in the Control Panel? Go to step 3. Correct the paper settings in the Control Panel. Go to step 3. 3 Check the paper type. • Paper in the tray • Paper type setting in the Control Panel • Paper type of the printing job Go to step 4. Correct the paper type setting in the Control Panel. 4 1. Reseat Tray 2. 2. Does the error still occur? Go to step 5. Complete. 5 1. Check the No Paper Actuator. 2. Does the Actuator operate smoothly? Go to step 6. Replace the Feeder Assembly. 6 1. Perform the Tray 2 No Paper test: Service Mode > Engine Diag > Sensor Test > Tray 2 No Paper. 2. Does the number on the Control Panel increase by 1 every time the Actuator is activated? Replace the MCU Board. Go to step 7. 7 1. Check the wiring harness connectors P/J29, P/J292, and P/ J2921 between the No Paper Sensor and the MCU Board. 2. Are the connectors securely connected? Go to step 8. Reconnect the connectors. Go to step 8. 8 Check the Right Side Harness for continuity. 1. Disconnect P/J29 from the MCU Board and P/J292 from the Regi Sensor Harness. 2. Check continuity between P/J29 <=> P/J292. Go to step 9. Replace the Right Side Harness. 9 Check the Registration Sensor Harness for continuity. 1. Disconnect P/J292 from the Right Side Harness and P/J2921 from the No Paper Sensor. 2. Check continuity between P/J292 <=> P/J2921. Go to step 10. Replace the Registration Sensor Harness. 10 Check the No Paper Sensor signal. 1. Disconnect P/J29 from the MCU Board. 2. Is there +3.3 V across ground <=> J29-5 pin? Go to step 11. Replace the MCU Board. 11 Check the No Paper Sensor for operation. 1. Measure the voltage across ground <=> J29-7 pin. 2. Does the voltage change when the No Paper Actuator of the No Paper Sensor is activated? Replace the MCU Board. Replace the No Paper Sensor.

← Xem tất cả mã lỗi Xerox Phaser 6280

Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie