Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Xerox Phaser 6280

Code: 010-317

Description: Insert Fuser The printer does not detect the presence of the Fuser. Warning The Fuser may be hot. Turn the printer power Off and allow at least 5 minutes for the Fuser to cool before removing the Fuser.
Causes: • Fuser, PL6.1.10 • Fuser Harness, PL6.1.11 • MCU Board, PL9.1.20
Remedy: 1 1. Check the Fuser for correct installation. 2. Is the Fuser correctly installed? Go to step 3. Reseat the Fuser. Go to step 2. 2 Does the error still occur? Go to step 3. Complete. 3 1. Check the wiring harness connectors P/ J17 and P/J171 between the MCU Board and the Fuser.* 2. Are the connectors securely connected? Go to step 4. Reconnect the connectors. Go to step 4. 4 Check the Fuser Harness for continuity. 1. Disconnect P/J17 from the MCU Board and P/J171 from the Fuser. 2. Check continuity between P/J17 <=> P/ J171. Go to step 5. Replace the Fuser Harness. 5 1. Replace the Fuser. 2. Does the error still occur? Replace the MCU Board. Complete.

Code: 010-351

Description: Replace Fuser The Fuser has reached its end of life. Warning The Fuser may be hot. Turn the printer power Off and allow at least 5 minutes for the Fuser to cool before removing the Fuser.
Causes: • Fuser, PL6.1.10 • MCU Board, PL9.1.20
Remedy: 1 1. Check the Fuser life using CentreWare IS. 2. Does the Level show 0%? Replace the Fuser. Go to step 2. 2 Is the Fuser correctly installed? Go to step 3. Reseat the Fuser. 3 Does the error still occur? Go to step 4. Complete. 4 1. Replace the Fuser. 2. Does the error still occur? Replace the MCU Board. Complete.

Code: 010-359

Description: Fuser CRUM ID Error The Fuser CRUM ID error is detected. The Fuser CRUM ID read by the sensor is different from the one that was recorded. Warning The Fuser may be hot. Turn the printer power Off and allow at least 5 minutes for the Fuser to cool before removing the Fuser.
Causes: • Fuser, PL6.1.10 • MCU Board, PL9.1.20
Remedy: 1 1. Check the Fuser for correct installation. 2. Is the Fuser correctly installed? Go to step 3. Reseat the Fuser. Go to step 2. 2 Does the error still occur? Go to step 3. Complete. 3 1. Replace the Fuser. 2. Does the error still occur? Replace the MCU Board. Complete.

Code: 010-397

Description: Fuser Error The Fuser temperature regulation has failed. The NC sensor circuit in the MCU is defective. Warning The Fuser may be hot. Turn the printer power Off and allow at least 5 minutes for the Fuser to cool before removing the Fuser.
Causes: • Fuser, PL6.1.10 • Fuser Harness, PL6.1.11 • LVPS, PL9.1.4 • MCU Board, PL9.1.20 • Top LV Harness, PL10.1.16
Remedy: 1 1. Check the Fuser for correct installation. 2. Is the Fuser correctly installed? Go to step 2. Reseat the Fuser. Go to step 2. 2 Does the error still occur? Go to step 3. Complete. 3 1. Check the wiring harness connectors P/ J13, P/J17, P/J171, P/J47, and P/J501. 2. Are the connectors securely connected? Go to step 4. Reconnect the connectors. Go to step 4. 4 Check the Fuser Harness for continuity. 1. Disconnect P/J17 from the MCU Board and P/J171 from the Fuser. 2. Check continuity between P/J17 <=> P/ J171. Go to step 5. Replace the Fuser Harness. 5 Check the Top LV Harness for continuity. 1. Disconnect P/J 47 and P/J501 from the LVPS. 2. Disconnect P/J13 from the MCU Board. 3. Check continuity between: • P/J47 <=> P/J171 • P/J501 <=> P/J13 Go to step 6. Replace the Top LV Harness. 6 1. Replace the Fuser. 2. Does the error still occur? Go to step 7. Complete. 7 1. Replace the LVPS. 2. Does the error still occur? Replace the MCU Board. Complete.

Code: 010-421

Description: Ready Fuser Life The Fuser has reached its end of life. Warning The Fuser may be hot. Turn the printer power Off and allow at least 5 minutes for the Fuser to cool before removing the Fuser.
Causes: • Fuser, PL6.1.10 • MCU Board, PL9.1.20
Remedy: 1 1. Check the Fuser life using CentreWare IS. 2. Does the Level show 0%? Replace the Fuser. Go to step 2. 2 1. Check the Fuser for correction installation. 2. Is the Fuser correctly installed? Go to step 3. Reseat the Fuser. Go to step 3. 3 Does the error still occur? Go to step 3. Complete. 4 1. Replace the Fuser. 2. Does the error still occur? Replace the MCU Board. Complete.

Code: 016-500, 016-501, 016-502

Description: Download Error An error occurred because an invalid firmware was installed. • Chain Link 016-500: Erase Flash Error (Download Delete Error) • Chain Link 016-501: Write Flash Error (Download Write Error) • Chain Link 016-502: Verify Flash Error (Download Verify Error)
Causes: • Image Process Board, PL9.1.27
Remedy: 1 1. Check the Image Processor Board for correct installation. 2. Is the Image Processor Board correctly installed? Go to step 2. Reseat the Image Processor Board. Go to step 2. 2 1. Does the error still occur? Replace the Image Processor Board. Complete.

Code: 016-610

Description: Control Panel Language Set Unsupported The Control Panel does not support the language.
Causes: • MCU Board, PL9.1.20
Remedy: 1 1. Turn the printer power Off and back On. 2. Does the error still occur? Replace the MCU Board. Complete.

Code: 016-612

Description: MAC Address Error MAC Address error occurs.
Causes: • Image Processor Board, PL9.1.27
Remedy: 1 1. Reboot the printer. 2. Does the error still occur? Go to step 2. Complete. 2 1. Reseat the Image Processor Board. 2. Does the error still occur? Replace the Image Processor Board. Complete.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie