Code: 024-960
Description: Load Tray 3 (No Suitable Paper) The type or size of paper mismatched or Tray 3 is empty.
Causes: • MCU Board, PL9.1.20 • Right Side Harness, PL10.1.15 • Tray 3 Feeder Harness, PL12.2.3 • Optional Feeder Board, PL12.2.6 • C2 Chute Harness, PL12.2.7 • Tray 3 Feeder Assy., PL12.3.1 • No Paper Sensor, PL12.3.14 • No Paper Actuator, PL12.3.25 • C2 No Paper Harness, PL12.3.30 • Tray 3, PL12.4.1
Remedy: 1 1. Check the paper size. 2. Does the paper size meet specifications? Go to step 2. Replace the paper with the correct specifications. 2 1. Check the paper size setting. 2. Does the paper match with the settings in the Control Panel? Go to step 3. Correct the paper settings in the Control Panel. Go to step 3. 3 Check the paper type. • Paper in the tray • Paper type setting in the Control Panel • Paper type of the printing job Go to step 4. Correct the paper type setting in the Control Panel. 4 1. Reseat Tray 3. 2. Does the error still occur? Go to step 5. Complete. 5 1. Check the No Paper Actuator. 2. Does the Actuator operate smoothly? Go to step 6. Replace the Tray 3 Feeder Assembly. 6 1. Perform the Tray 3 No Paper test: Service Mode > Engine Diag > Sensor Test > Tray 3 No Paper. 2. Does the number on the Control Panel increase by 1 every time the Actuator is activated? Replace the MCU Board. Go to step 7. 7 1. Check the wiring harness connectors P/J421, P/J4212, and P/ J42121 between the No Paper Sensor and the Tray 3 Feeder Board. 2. Are the connectors securely connected? Go to step 8. Reconnect the connectors. 8 Check the C2 Chute Harness for continuity. 1. Disconnect P/J421 from the Optional Feeder Board and P/J4212 from the C2 No Paper Harness. 2. Check continuity between P/J421 <=> P/J4212. Go to step 9. Replace the Optional Sheet Feeder. 9 Check the C2 No Paper Harness for continuity. 1. Disconnect P/J4212 from the C2 Chute Harness and P/J42121 from the No Paper Sensor. 2. Check continuity between P/J4212 <=> P/J42121. Go to step 10. Replace the Tray 3 Feeder Assembly. 10 Check the No Paper Sensor signal. 1. Disconnect P/J421 from the MCU Board. 2. Is there +3.3 V across ground <=> J421-3 pin? Go to step 11. Go to step 12. 11 Check the No Paper Sensor for operation. 1. Measure the voltage across ground <=> J421-5 pin. 2. Does the voltage change when the No Paper Actuator of the No Paper Sensor is activated? Go to step 12. Replace the No Paper Sensor. 12 1. Replace the Tray 3 Feeder Assembly. 2. Does the error still occur? Complete. Replace the MCU Board. 13 1. Check the wiring harness connectors P/J419, P/J281, and P/ J28. 2. Are the connectors securely connected? Go to step 14. Reconnect the connectors. Go to step 14. 14 Check the Optional Feeder Harness for continuity. 1. Disconnect P/J419 from the Optional Feeder Board and P/J281 from the Right Side Harness. 2. Check continuity between P/J419 <=> P/J281. Go to step 15. Replace the Optional Sheet Feeder. 15 Check the Right Side Harness for continuity. 1. Disconnect P/J281 from the Feeder Unit Harness and P/J28 from the MCU Board. 2. Check continuity between P/J281 <=> P/J28. Go to step 16. Replace the Right Side Harness. 16 Check the Optional Feeder Board signal. 1. Disconnect P/J28 on the MCU Board. 2. Is there +3.3 V across ground <=> J28-7 pin? Replace the Tray 3 Feeder Assembly. Replace the MCU Board.