Code: 042-325-04
Description: Optional Feeder Motor Error The Optional Feeder Motor has failed.
Causes: • MCU Board, PL9.1.20 • Feed Roll, PL12.1.9 • Retard Roll, PL12.3.10 • Right Side Harness, PL10.1.15 • Optional 550-Sheet Feeder, PL12.1.1 • Feeder Unit Harness, PL12.2.3 • Tray 3 Feeder Board, PL12.2.6 • C2 Motor Harness, PL12.2.9 • Tray 3 Feeder Drive, PL12.2.10 • Tray 3 Feeder Assembly, PL12.3.1
Remedy: 1 1. Check the detailed error code (press the Up and Down buttons simultaneously). 2. Does code "04" display on the Control Panel? Go to step 2. 2 1. Check the paper tray for correct installation. 2. Is the tray correctly installed? Go to step 4. Reseat the paper tray. Go to step 3. 3 Does the error still occur? Go to step 4. Complete. 4 1. Check the Feed Rollers and Retard Rollers for rotation. 2. Do the Rollers rotate smoothly? Go to step 5. Replace the defective Roller(s). 5 1. Check the wiring harness connectors P/J422, P/J4221, and P/ J4222 between the Tray 3 Feeder Board and the Tray 3 Feeder Drive Assembly. 2. Are the connectors securely connected? Go to step 6. Reconnect the connectors. Go to step 6. 6 1. Perform the Tray 3 Feed Motor test: Service Mode > Engine Diag > Motor Test > Tray 3 Feed Motor. 2. Does the Motor operate properly? Replace the MCU Board. Go to step 7. 7 1. Check the Tray 3 Drive Feeder Assembly for correct installation. 2. Is the Tray 3 Drive Feeder Assembly correctly installed? Go to step 8. Reseat the Tray 3 Drive Feeder. Go to step 8. 8 Does the error still occur? Go to step 9. Complete. 9 Check the C2 Motor Harness for continuity. 1. Disconnect P/J422 and P/J4222. 2. Check continuity between P/J422 <=> P/J4222. Go to step 10. Replace the Optional Sheet Feeder. 10 Check the Tray 3 Feeder Drive for signal. 1. Disconnect P/J422 from the Tray 3 Feeder Board. 2. Is the +24 V across ground <=> J422-6 pin when the Interlock Switch is activated? Replace the Optional 550- Sheet Feeder. Go to step 11. 11 1. Check the wiring harness connectors P/J419, P/J281, and P/ J28 between the Tray 3 Feeder Board and the MCU Board. 2. Are the connectors securely connected? Go to step 12. Reconnect the connectors. 12 Check the Feeder Unit Harness for continuity. 1. Disconnect P/J419 from the Feeder Board and P/J281 from the MCU Board. 2. Check continuity between P/J419 <=> P/J281. Go to step 13. Replace the Optional Sheet Feeder. 13 Check the Right Side Harness for continuity. 1. Disconnect P/J281 from the Feeder Harness and P/J28 from the MCU Board. 2. Check continuity between P/J281 <=> P/J28. Go to step 14. Replace the Right Side Harness. 14 Check the Tray 3 Feeder Board signal. 1. Disconnect P/J28 from the MCU Board. 2. Are there +24 V across ground <=> J28-4/J28-5 pin when the Interlock Switch is activated? Replace the Optional 550- Sheet Feeder. Replace the MCU Board.