Code: 042-358-01
Description: Fan Motor Error (Rear) The MCU has detected an error upon receiving signal from the Rear Fan.
Causes: • Front Cover Harness, PL1.2.11 • LVPS, PL9.1.4 • Main Fan, PL9.1.10 • MCU Board, PL9.1.20 • Right Side Harness, PL10.1.15 • Top LV Harness, PL10.1.16 • Duplex Unit, PL11.1.1 • Duplex Unit Harness, PL11.1.18 • Duplex Fan, PL11.1.25
Remedy: 1 1. Check the detailed error code (press the Up and Down buttons simultaneously). 2. Does code “01” display on the Control Panel? Go to step 2. Go to step 7. 2 1. Check wiring harness connectors between the Main Fan and the LVPS. 2. Is P/J502 securely connected? Go to step 3. Complete. 3 Does the error still occur? Go to step 4. Complete. 4 1. Perform the Fan test: Service Mode > Engine Diag > Motor Test > Fan. 2. Does the Fan operate properly? Replace the MCU Board. Go to step 5. 5 Check the Top LV Harness for continuity. 1. Disconnect P/J501 from the LVPS and P/J13 from the MCU Board. 2. Check continuity between P/J501 <=> P/J13. Go to step 6. Replace the Top LV Harness. 6 Check the LVPS signal. 1. Disconnect P/J503 from the LVPS. 2. Is there +24 V across ground <=> J503-1 pin when the Interlock Switch is activated? Replace the MCU Board. Replace the LVPS. 7 1. Check the detailed error code (press the Up and Down buttons simultaneously). 2. Does code “02” display on the Control Panel? Go to step 8. Go to step 1. 8 1. Check the wiring harness connectors between the Duplex Fan and the Duplex Board. 2. Is P/J427 securely connected? Go to step 9. Reconnect the wiring harness connector. 9 Does the error still occur? Go to step 10. Complete. 10 1. Perform the Duplex Fan test: Service Mode > Engine Diag > Duplex Fan. 2. Does the Motor operate properly? Replace the MCU Board. Go to step 11. 11 1. Check the wiring harness connectors P/J428, P/J2720, P/ J272, and P/J27 between the MCU Board and Duplex Board. 2. Are the connectors securely connected? Go to step 12. Reconnect the connectors. 12 Check the Duplex Unit Harness for continuity. 1. Disconnect P/J428 from the Duplex Board and P/J2720 Front Cover Assembly Harness. 2. Check continuity between P/J2720 <=> P/J428. Go to step 13. Replace the Duplex Unit. 13 Check the Front Cover Harness for continuity. 1. Disconnect P/J2720 from the Front Cover Harness and P/J272 from the Right Side Harness. 2. Check continuity between P/J2720 <=> P/J272. Go to step 14. Replace the Front Cover Harness. 14 Check the Right Side Harness for continuity. 1. Disconnect P/J27 from the MCU Board and P/J272 from the Front Cover Harness. 2. Check continuity between P/J27 and P/J272. Go to step 15. Replace the Right Side Harness. 15 Check the Duplex Board signal. 1. Disconnect P/J27 from the MCU Board. 2. Are there +24 V across ground <=> J27-17/J27-18 pin when the Interlock is activated? Replace the Duplex Unit. Replace the MCU Board.