Code: 092-651
Description: ADC Sensor Error (Low Density) The ADC Sensor has detected low density error.
Causes: • Front Cover Harness, PL1.2.11 • Transfer Unit, PL4.1.1 • Laser Unit, PL5.1.2 • Print Cartridge (C/M/Y/K), PL5.1.18-21 • Main Drive Assembly, PL8.1.2 • MCU Board, PL9.1.20 • Right Side Harness, PL10.1.15
Remedy: 1 1. Check the detailed error code on the Control Panel (press the Up and Down buttons simultaneously). 2. Does code “02” display on the Control Panel? Go to step 3. Go to step 13. 2 1. Check the Transfer Unit for correct installation. 2. Is the Transfer Unit correctly installed? Go to step 4. Reseat the Transfer Unit. Go to step 3. 3 Does the error still occur? Go to step 4. Complete. 4 1. Check the Print Cartridges for correct installation. 2. Are the Print Cartridges correctly installed? Go to step 6. Reseat the Print Cartridge(s). Go to step 5. 5 Does the error still occur? Go to step 6. Complete. 6 1. Check the toner density. Perform Gradation Test Print: Service Mode > Test Print > Gradation ESS. 2. Compare the density of four colors toner. Is there dark color on the print? Go to step 7. Replace the MCU Board. 7 Check the Solenoid in the Transfer Unit for operation. 1. Perform the ADC Sensor Solenoid test: Service Mode > Engine Diag > Motor Test > ADC (CTD) Sensor Solenoid. 2. Perform the ADC Sensor LED test: Service Mode > Engine Diag > Motor Test > ADC (CTD) Sensor LED. 3. Does the ADC Sensor operate properly? Go to step 12. Go to step 8. 8 1. Check the wiring harness connectors P/J27, P/J272, and P/ J2721 between the MCU Board and the Transfer Unit. 2. Are the connectors securely connected? Go to step 9. Reconnect the connectors. Go to step 9. 9 Check the Front Cover Harness for continuity. 1. Disconnect P/J2721 from the Transfer Unit and P/J272 from the Right Side Harness. 2. Check continuity between P/J2721 <=> P/J272. Go to step 10. Replace the Front Cover Harness. 10 Check the Right Side Harness for continuity. 1. Disconnect P/J27 from the MCU Board and P/J272 from the Front Cover Harness. 2. Check continuity between P/J27 <=> P/J272. Go to step 11. Replace the Right Side Harness. 11 Check the ADC Sensor signal. 1. Disconnect P/J27 from the MCU Board. 2. Is there +5 V across ground <=> J27-7 pin? Replace the Transfer Unit. Replace the MCU Board. 12 1. Replace the corresponding Print Cartridge. 2. Does the error still occur? Replace the Laser Unit. Complete. 13 1. Check the detailed error code on the Control Panel (press the Up and Down buttons simultaneously). 2. Does code “01” display on the Control Panel? Go to step 14. Go to step 1. 14 1. Check the Transfer Unit for correct installation. 2. Is the Transfer Unit correctly installed? Go to step 16. Reseat the Transfer Unit. Go to step 15. 15 Does the error still occur? Go to step 16. Complete. 16 1. Check the toner density. Perform Gradation Test Print: Service Mode > Test Print > Gradation ESS. 2. Compare the density of four colors toner. Is there dark color on the print? Go to step 17. Replace the MCU Board. 17 Check the Solenoid in the Transfer Unit for operation. 1. Perform the ADC Sensor Solenoid test: Service Mode > Engine Diag > Motor Test > ADC (CTD) Sensor Solenoid. 2. Perform the ADC Sensor LED test: Service Mode > Engine Diag > Motor Test > ADC (CTD) Sensor LED. 3. Does the ADC Sensor operate properly? Replace the corresponding Print Cartridge. Go to step 18. 18 1. Check the wiring harness connectors P/J27, P/J272, and P/ J2721 between the MCU Board and the Transfer Unit. 2. Are the connectors securely connected? Go to step 19. Reconnect the connectors. Go to step 19. 19 Check the Front Cover Harness for continuity. 1. Disconnect P/J2721 from the Transfer Unit and P/J272 from the Right Side Harness. 2. Check continuity between P/J2721 <=> P/J272. Go to step 20. Replace the Front Cover Harness. 20 Check the Right Side Harness for continuity. 1. Disconnect P/J27 from the MCU Board and P/J272 from the Front Cover Harness. 2. Check continuity between P/J27 <=> P/J272. Go to step 21. Replace the Right Side Harness. 21 Check the ADC Sensor signal. 1. Disconnect P/J27 from the MCU Board. 2. Is there +5 V across ground <=> J27-7 pin? Replace the Transfer Unit. Replace the MCU Board