Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi 093-919 ... 093-922 — Xerox Phaser 6280

Code: 093-919 ... 093-922

Description: Check Cartridge (Yellow/Magenta/Cyan/Black) The Print Cartridge (Yellow/Magenta/Cyan/Black) tape was not removed when a new Print Cartridge is installed. • Chain Link 093-919: IOT Yellow Cartridge Tape Staying • Chain Link 093-920: IOT Magenta Cartridge Tape Staying • Chain Link 093-921: IOT Cyan Cartridge Tape Staying • Chain Link 093-922: IOT Black Cartridge Tape Staying
Causes: • Dispenser Assy., PL5.1.12 • Print Cartridge (Y/M/C/K), PL5.1.18-21 • MCU Board, PL9.1.20 • Top LV Harness, PL10.1.16
Remedy: 1 1. Check the Print Cartridge tape. 2. Has the tape been removed? Go to step 2. Remove the tape on the Print Cartridge. Go to step 2. 2 Does the error still occur? Go to step 3. Complete. 3 1. Replace the Print Cartridge. 2. Does the error still occur? Go to step 4. Complete. 4 Perform the Toner Motor test: Service Mode > Engine Diag > Motor Test > Toner Motor. While testing the Toner Motor, close the Interlock Harness. • Yellow Toner Motor • Magenta Toner Motor • Cyan Toner Motor • Black Toner Motor Check the gear of the Auger for damage. If the gear is damaged, replace the Dispenser Assembly. Go to step 5. 5 1. Check the Dispenser wiring harness connectors. • Yellow: P/J18 and P/J181 • Magenta: P/J18 and P/J182 • Black: P/J18 and P/J183 • Cyan: P/J18 and P/J184 2. Are the connectors securely connected? Go to step 6. Reconnect the connectors. Go to step 6. 6 Does the error still occur? Go to step 7. Complete. 7 Check the Top LV Harness for continuity. 1. Disconnect P/J Harnesses. • Yellow: P/J18 from the MCU Board and P/J181 from the Dispenser Assembly • Magenta: P/J18 from the MCU Board and P/J182 from the Dispenser Assembly • Black: P/J18 from the MCU Board and P/J183 from the Dispenser Assembly • Cyan: P/J18 from the MCU Board and P/J184 from the Dispenser Assembly 2. Check continuity between P/J connectors: • Yellow: P/J18 <=> P/J181 • Magenta: P/J18 <=> P/J182 • Black: P/J18 <=> P/J183 • Cyan: P/J18 <=> P/J184 Go to step 8. Complete. 8 Check the Dispenser Assembly signal. 1. Disconnect P/J18 from the MCU Board. 2.When the Interlock Switch is activated, is there +24 V across: • Ground <=> P/J18-A1/P/J18-A2 pin (Yellow) • Ground <=> P/J18-A7/P/J18-A8 pin (Magenta) • Ground <=> P/J18-B1/P/J18-B2 pin (Black) • Ground <=> P/J18-B7/P/J18-B8 pin (Cyan) Replace the Dispenser Assembly. Replace the MCU Board.

← Xem tất cả mã lỗi Xerox Phaser 6280

Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie