Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi 012-211 — Xerox WorkCentre 5225

Code: 012-211

Description: Stacker Tray Failure RAP After Stacker Tray started descending, the Stack Height Sensor did not turn Off within the specified time.
Remedy: Check the tray raise/lower mechanism for foreign substances and distortion. No distortion or foreign substances are found in the tray raise/lower mechanism. Y↓N→Clear away the foreign substances. Correct the distortion. Execute Component Control[012-264 Stack Height Sensor 1]. Actuate the Stack Height Sensor 1 with paper. The display changes. Y↓N→Check the connections of J8873 and P/J8988. J8873 and P/J8988 are connected correctly. Y↓N→Connect J8873 and P/J8988. Check the wire between J8873 and J8988 for an open circuit or a short circuit. The wire between J8873 and J8988 is conducting without an open circuit or a short circuit. Y↓N→Repair the open circuit or short circuit. Measure the voltage between the Finisher PWB P8988-16 (+) and GND (-). The voltage is approx. +5VDC. Y↓N→Replace the Finisher PWB (PL 23.16). Measure the voltage between the Finisher PWB P8988-17 (+) and GND (-). Actuate the Stack Height Sensor 1 with paper. The voltage changes. Y↓N→Replace the Stack Height Sensor 1 (PL 23.11). Replace the Finisher PWB (PL 23.16). Execute Component Control[012-265 Stack Height Sensor 2]. Actuate the Stack Height Sensor with paper. The display changes. Y↓N→Check the connections of J8874 and P/J8988. J8874 and P/J8988 are connected correctly. Y↓N→Connect J8874 and P/J8988. Check the wire between J8874 and J8988 for an open circuit or a short circuit. The wire between J8874 and J8988 is conducting without an open circuit or a short circuit. Y↓N→Repair the open circuit or short circuit. Measure the voltage between the Finisher PWB P8988-19 (+) and GND (-). The voltage is approx. +5VDC. Y↓N→Replace the Finisher PWB (PL 23.16). Measure the voltage between the Finisher PWB P8988-20 (+) and GND (-). Actuate the Stack Height Sensor with paper. The voltage changes. Y↓N→Replace the Stack Height Sensor 2 (PL 23.11). Replace the Finisher PWB (PL 23.16). Alternately execute Component Control[012-060 Stacker Motor up ON] and Component Control[ 012-061 Stacker Motor down ON]. The Stacker Motor (PL 23.7) starts up. Y↓N→Check the connections of P/J8986. P/J8986 are connected correctly. Y↓N→Connect P/J8986. Check the wires on P8986 for an open circuit or a short circuit. The wires on P8986 is conducting without an open circuit or a short circuit. Y↓N→Repair the open circuit or short circuit. Replace the Stacker Motor (PL 23.7). If the problem persists, replace the Finisher PWB (PL 23.16). Replace the Finisher PWB (PL 23.16). If the problem persists, replace the MCU PWB (PL 9.1).

← Xem tất cả mã lỗi Xerox WorkCentre 5225

Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie