Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi 012-221 — Xerox WorkCentre 5225

Code: 012-221

Description: (A-Finisher) Front Tamper Home Sensor ON Fail During the moving of the Front Tamper, when the Front Tamper Home Sensor was Off, to the home position, the Front Tamper Home Sensor did not detected turning On within a specified time after the Front Tamper started moving.
Remedy: Check the Front Tamper for any foreign object, deformation and binding that prevents it from moving. The Front Tamper is defects and binding. Y↓N→Repair the deformation and remove the foreign object(s) and the binding. Check the drive mechanism to the Front Tamper for a deformed or broken part and not-seated gears. The drive mechanism is free from defects and the gears seat properly. Y↓N→Repair the Front Tamper mechanism. Run DC330[012-220]. Enter Component Control [012-220]. Move the Front Tamper by hand to block and unblock the Front Tamper Home Sensor. The display changes. Y↓N→Check the connections of P/J8700 and P/J8724. P/J8700 and P/J8724 are securely connected. Y↓N→Connect P/J8700 and P/J8724 securely. Check for an open or short circuit between J8700 and J8724. The wires between J8700 and J8724 are OK. Y↓N→Repair the open wire or short circuit. Measure the voltage between Finisher PWB J8700-6 (+) and GND (-). The voltage is approx. +5VDC. Y↓N→Go to Wirenet A-Finisher +5VDC and check the +5VDC circuit. Measure the voltage between Finisher PWB J8700-5 (+) and GND (-). Move the Front Tamper by hand to block and unblock the Front Tamper Home Sensor. The voltage changes. Y↓N→Replace the Front Tamper Home Sensor (PL 22.10). Check the wires and connectors for an intermittent open or short circuit. If the problem continues, replace the Finisher PWB (PL 22.7). Enter [012-020] and [012-023] alternately. The Front Tamper Motor rotates. Y↓N→Check the connections of P/J8710, P/J8738A and P/J8738B. P/J8710 P/J8738A and P/J8738B are securely connected. Y↓N→Connect P/J8710, P/J8738A and P/J8738B securely. Check for an open or short circuit between J8710, P/J8738A and J8738B. The wires between are OK. Y↓N→Repair the open or short circuit. Measure the voltage between Finisher PWB J8710-5 (+) and GND (-), and between J8710-7 (+) and GND (-). The voltage is approx. +24VDC. Y↓N→Go to Wirenet A-Finisher +24VDC and check the +24VDC circuit. If the problem continues, replace the Finisher PWB (PL 22.7). Replace the Front Tamper Motor (PL 22.10). If the problem continues, replace the Finisher PWB (PL 22.7). Check the wires and connectors for an intermittent open or short circuit. If the problem continues, replace the Finisher PWB (PL 22.7).

← Xem tất cả mã lỗi Xerox WorkCentre 5225

Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie