Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi 012-224 — Xerox WorkCentre 5225

Code: 012-224

Description: (A-Finisher) Rear Tamper Home Sensor OFF Fail • At the end of the operation of trying to turn Off the Rear Tamper Home Sensor that was On, the Rear Tamper Home Sensor was not detected being Off. • The Rear Tamper Home Sensor should have turned Off and then the Rear Tamper Motor stopped, but the Rear Tamper Home Sensor was On.
Remedy: Check the Rear Tamper for any foreign object, deformation and binding that prevents it from moving. The Rear Tamper is free from defects and binding. Y↓N→Repair the deformation and remove the foreign object(s) and the binding. Check the drive mechanism to the Rear Tamper for a deformed or broken part and not-seated gears. The drive mechanism is in normal condition, not deformed or broken and with no not-seated gears. Y↓N→Repair the Rear Tamper drive mechanism. Enter Component Control [012-221]. Move the Rear Tamper by hand to block and unblock the Rear Tamper Home Sensor. The display of changes. Y↓N→Check the connections of P/J8700 and P/J8726. P/J8700 and P/J8726 are securely connected. Y↓N→Connect P/J8700 and P/J8726 securely. Check for an open or short circuit between J8700 and J8726. The wires between J8700 and J8726 are OK. Y↓N→Repair the open wire or short circuit. Measure the voltage between Finisher PWB J8700-12 (+) and GND (-). The voltage is approx. +5VDC. Y↓N→Go to Wirenet A-Finisher +5VDC and check the +5VDC circuit. Measure the voltage between Finisher PWB J8700-11 (+) and GND (-). Move the Rear Tamper by hand to block and unblock the Rear Tamper Home Sensor. The voltage changes. Y↓N→Replace the Rear Tamper Home Sensor (PL 22.9). Check the wires and connectors for an intermittent open or short circuit. If the problem continues, replace the Finisher PWB (PL 22.7). Enter [012-026] and [012-029] alternately. The Rear Tamper Motor rotates. Y↓N→Check the connections of P/J8710, P/J8737A and P/J8737B. P/J8710, P/J8737A and P/J8737B are securely connected. Y↓N→Connect P/J8710, P/J8737A and P/J8737B securely. Check for an open wire or short circuit between J8710, P/J8737A and J8737B. The wire between J8710, P/J8737A and J8737B are OK. Y↓N→Repair the open or short circuit. Measure the voltage between Finisher PWB J8710-1 (+) and GND (-), and between J8710-3 (+) and GND (-). The voltage is approx. +24VDC. Y↓N→Go to Wirenet A-Finisher +24VDC and check the +24VDC circuit. If the problem continues, replace the Finisher PWB (PL 22.7). Repair the Rear Tamper Motor (PL 22.10). If the problem continues, replace the Finisher PWB (PL 22.7). Check the wires and connectors for an intermittent open or short circuit. If the problem continues, replace the Finisher PWB (PL 22.7).

← Xem tất cả mã lỗi Xerox WorkCentre 5225

Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie