Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi 024-930 — Xerox WorkCentre 5225

Code: 024-930

Description: (A-Finisher) Stacker Tray Full Stack One of the following: • At Power On, the Stack Height Sensor detected the height and the Full position. • During the operation of adjusting (lowering) the height of the Stacker Tray for small paper to be ejected, the Full position was detected. • During the operation of adjusting (lowering) the height of the Stacker Tray for large paper to be ejected, the Half position (Full-of-Large-Sheets position) was detected. • With the Half position (Full-of-Large-Sheets position) already detected, paper (large paper) a stack of which is limited to the Half position was ejected.
Remedy: Check for remaining paper and foreign objects on the Stacker Tray. The Stacker Tray is free of paper or foreign objects. Y↓N→Remove the remaining paper and/or foreign object(s). Check the drive mechanism to the Stacker Tray for a deformed or broken part and not-seated gears. The drive mechanism is in normal condition, not deformed or broken and with no not-seated gears. Y↓N→Repair the Stacker Tray mechanism. Enter Component Control [012-267]. Block and unblock the Stack Height Sensor with a piece of paper. The display changes. Y↓N→Check the connections of P/J8708 and P/J8727. P/J8708 and P/J8727 are securely connected. Y↓N→Connect P/J8708 and P/J8727 securely. Check for an open or short circuit between J8708 and J8727. The wires between J8708 and J8727 are OK. Y↓N→Repair the open or short circuit. Measure the voltage between J8708-3 (+) on the Finisher PWB and GND (-). The voltage is approx. +5VDC. Y↓N→Go to Wirenet A-Finisher +5VDC and check the +5VDC circuit. Measure the voltage between J8708-2 (+) on the Finisher PWB and GND (-). Block and unblock the Stack Height Sensor with a piece of paper. The voltage changes. Y↓N→Replace the Stack Height Sensor (PL 22.10). Check the wires and connectors for an intermittent open or short circuit. If the problem continues, replace the Finisher PWB (PL 22.7). Run DC330[012-278]. Enter [012-278]. Rotate the Stacker Stack Sensor 1 actuator by hand to block and unblock the sensor. The display changes. Y↓N→Check the connections of P/J8707 and P/J8722. P/J8707 and P/J8722 are securely connected. Y↓N→Connect P/J8707 and P/J8722 securely. Check for an open or short circuit between J8707 and J8722. The wires between J8707 and J8722 are OK. Y↓N→Repair the open or short circuit. Measure the voltage between J8707-6 (+) on the Finisher PWB and GND (-). The voltage is approx. +5VDC. Y↓N→Go to Wirenet A-Finisher +5VDC and check the +5VDC circuit. Measure the voltage between J8707-5 (+) on the Finisher PWB and GND (-). Rotate the Stacker Stack Sensor 1 actuator by hand to block and unblock the sensor. The voltage changes. Y↓N→Replace the Stacker Stack Sensor 1 (PL 22.8). Check the wires and connectors for an intermittent open or short circuit. If the problem continues, replace the Finisher PWB (PL 22.7). Enter [012-279]. Rotate the Stacker Stack Sensor 2 actuator by hand to block and unblock the sensor. The display changes. Y↓N→Check the connections of P/J8707 and P/J8721. P/J8707 and P/J8721 are securely connected. Y↓N→Connect P/J8707 and P/J8721 securely. Check for an open or short circuit between J8707 and J8721. The wires between J8707 and J8721 are OK. Y↓N→Repair the open or short circuit. Measure the voltage between J8707-3 (+) on the Finisher PWB and GND (-). The voltage is approx. +5VDC.

← Xem tất cả mã lỗi Xerox WorkCentre 5225

Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie