Code: 073-210
Description: Tray 3 Lift Up Failure RAP • After the 2TM-Tray 3 Feed/Lift Motor turned On, the 2TM-Tray 3 Level Sensor did not turn On within the specified time. • After the TTM-Tray 3 Feed/Lift Motor turned On, the TTM-Tray 3 Level Sensor did not turn On within the specified time.
Remedy: Remove the tray and reinstall. The Tray 3 Feed/Lift Motor can be heard. Y↓N→Execute Component Control [073-009 Tray 3 Feed/Lift Motor ON]. The Tray 3 Feed/Lift Motor (PL 12.3/PL 13.6) can be heard. Y↓N→Check the connections of P/J220B, P/J661B and P/J549. P/J220B, P/J661B and P/J549 are connected correctly. Y↓N→Connect P/J220B, P/J661B and P/J549. Remove the Tray 3 Feed/Lift Motor (PL 12.3/PL 13.6) and the Tray 4 Feed/Lift Motor (PL 12.3/PL 13.6). Replace the Tray 3 Feed/Lift Motor with the Tray 4 Feed/Lift Motor. Execute Component Control [073-009 Tray 3 Feed/Lift Motor ON]. The Tray 4 Feed/Lift Motor (PL 12.3/PL 13.6) can be heard. Y↓N→Return the Tray 3 Feed/Lift Motor to its original position. Check the wire between J220B and J549 for an open circuit or a short circuit. The wire between J220B and J549 is conducting without an open circuit or a short circuit. Y↓N→Repair the open circuit or short circuit. Replace the Tray Module PWB (PL 12.6/PL 13.8). Return the Tray 4 Feed/Lift Motor to its original position. Replace the Tray 3 Feed/Lift Motor (PL 12.3/PL 13.6). Go to the OF 2 (SIZE SWITCH ASSY RAP). Check the installation of the Tray 3 Level Sensor (PL 12.3/PL 13.6) and the operation of the actuator. The Tray 4 Level Sensor is installed correctly and the actuator works. Y↓N→Reinstall the Tray 4 Level Sensor. Execute Component Control [071-208 Tray 3 Level Sensor]. Manually activate the Tray 3 Level Sensor (PL 12.3/PL 13.6). The display changes. Y↓N→Check the connections of P/J101B, P/J661B and P/J549. P/J101B, P/J661B and P/ J549 are connected correctly. Y↓N→Connect P/J101B, P/J661B and P/J549. Check the wire between J101B and J549 for an open circuit or a short circuit. The wire between J101B and J549 is conducting without an open circuit or a short circuit. Y↓N→Repair the open circuit or short circuit. Measure the voltage between the Tray Module PWB P549-B7 (+) and GND (-). The voltage is approx. +5VDC. Y↓N→Replace the Tray Module PWB (PL 12.6/PL 13.8). Measure the voltage between the Tray Module PWB P549-B9 (+) and GND (-). Activate the actuator of the Tray 3 Level Sensor (PL 12.3/PL 13.6). The voltage changes. Y↓N→Replace the Tray 3 Level Sensor (PL 12.3/PL 13.6). Replace the Tray Module PWB (PL 12.6/PL 13.8). Replace the Tray Module PWB (PL 12.6/PL 13.8).