Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi 074-103 — Xerox WorkCentre 5225

Code: 074-103

Description: Tray 3 Feed Out Sensor On JAM (Tray 4 Feed) RAP After the Tray 4 Feed Out Sensor turned On, the Tray 3 Feed Out Sensor did not turn On within the specified time.
Remedy: Check the Transport Roll for wear and paper powder. The Transport Roll is ok. Y↓N→Replace the Transport Roll. Check for foreign substances, distortion and paper powder in the paper transport path. No distortion, foreign substances, or paper powder are found in the paper transport path. Y↓N→Clear away the foreign substances and paper powder. Correct the distortion. Execute Component Control [071-101 Tray 3 Feed Out Sensor]. Actuate the Tray 3 Feed Out Sensor (PL 12.5/PL 13.5) with paper. The display changes. Y↓N→Check the connections of P/J821, P/J841, P/J548, P/J541 and P/J413. P/J821, P/ J841, P/J548, P/J541 and P/J413 are connected correctly. Y↓N→Connect P/J821, P/J841, P/J548, P/J541 and P/J413. Check the wire between J821 and J548 for an open circuit or a short circuit. The wire between J821 and J548 is conducting without an open circuit or a short circuit. Y↓N→Repair the open circuit or short circuit. Measure the voltage between the Tray Module PWB P548-8 (+) and GND (-). The voltage is approx. +5VDC. Y↓N→Replace the Tray Module PWB (PL 12.6/PL 13.8). Measure the voltage between the Tray Module PWB P548-10 (+) and GND (-). Actuate the Tray 3 Feed Out Sensor (PL 12.5/PL 13.5) with paper. The voltage changes. Y↓N→Replace the Tray 3 Feed Out Sensor (PL 12.5/PL 13.5). Check the wire between J541-10 and J413-B4 for an open circuit or a short circuit. The wire between J541-10 and J413-B4 is conducting without an open circuit or a short circuit. Y↓N→Repair the open circuit or short circuit. Measure the voltage between the MCU PWB P413-B4 (+) and GND (-). Actuate the Tray 3 Feed Out Sensor (PL 12.5/PL 13.5) with paper. The voltage changes. Y↓N→Replace the Tray Module PWB (PL 12.6/PL 13.8). Replace the MCU PWB (PL 9.1). Execute Component Control [073-006 2TM/TTM Takeaway Motor ON]. The 2TM/TTM Takeaway Motor (PL 12.6/PL 13.8) can be heard. Y↓N→Check the connections of P/J826 and P/J552. P/J826 and P/J552 are connected correctly. Y↓N→Connect P/J826 and P/J552. Check the wire between J826 and J552 for an open circuit or a short circuit. The wire between J826 and J552 is conducting without an open circuit or a short circuit. Y↓N→Repair the open circuit or short circuit. Replace the MCU PWB (PL 9.1). If the problem persists, replace the Tray Module PWB (PL 12.6/PL 13.8). Replace the MCU PWB (PL 9.1). If the problem persists, replace the Tray Module PWB (PL 12.6/PL 13.8).

← Xem tất cả mã lỗi Xerox WorkCentre 5225

Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie