Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi E3-1 — OKI B6100

Code: E3-1

Display: E3-1:REG JAM
Description: There is a paper jam between the Sensor Photo: Regi and the Sensor Exit in the Fuser Assy.
Fuser Assy within the specified time after the Sensor Photo:Regi activated.
Remedy: 1 INITIAL ANALYSIS Inspect the following components. • Clutch Regi • Sensor Photo:Regi • Actuator Regi • Roll Regi Metal • Roll Regi Rubber • BTR Assy • CRU • Harness Assy Regi (J43-J431, NJ432) • Harness Assy Conn (J23-J231) • PWBA Conn • PWBA HKB26 MCU • PWBA HKB PS • Gear Assy Drive Are they compatible with your printer version, correctly installed, not damaged, deformed, or contaminated? Go to step 2. Replace the problem components. 2 Is the paper that is loaded in the paper tray wrinkled or damaged? Replace with fresh, dry paper. Go to step 3. 3 Is there a sheet of paper at the Actuator Regi when the E3 code appears? Remove the jammed paper. Go to step 4. 4 PAPER SIZE ANALYSIS 1. Check the size of paper currently loaded. 2. A paper jam can occur if the paper used is larger or smaller than the maximum or minimum size specified for this printer. Does the paper size meet specifications? Go to step 5. Load paper that meets specifications. 5 GEAR ASSY DRIVE ANALYSIS 1. Use MAIN MOTOR TEST to check the Gear Assy Drive function. 2. Open the Cover Assy Front . 3. Remove the CRU . 4. Actuate the Switch Assy I/L Front . Do the transmission gears rotate correctly against those of the Roll Assy Turn , the Feeder Assy , Clutch Regi ? Go to step 7. Go to step 6. 6 CLUTCH REGI ANALYSIS Check the voltage between P/J43-1 and P/J43-2. Is there +24VDC between P/J43-1 and P/J43-2? Go to step 7. Go to 6.2 PWBA HKB PS Failure (+24VDC). 7 ROLL REGI METAL and ROLL REGI RUBBER ANALYSIS 1. Open the Cover Assy Front . 2. Remove the CRU . 3. Actuate the Switch Assy I/L Front . 4. Check the rotation of the Roll Regi Metal and Roll Regi Rubber using MAIN MOTOR TEST. Does the Roll Regi Metal and Roll Regi Rubber rotate properly? Go to step 8. Replace the P/H Assy . 8 SENSOR PHOTO: REGI ANALYSIS 1. Use SENSOR/ SWITCH CHECK to check the Sensor Photo:Regi. 2. Use a sheet of paper to actuate the sensor. Does the Sensor Photo: Regi function correctly and increment the Sensor Check number on the screen each time you actuate it? Go to step 11. Go to step 9. 9 HARNESS ASSY REGI (J43-J431, J432) ANALYSIS 1. Disconnect the Harness Assy Regi (J43-J431, J432) from the PWBA Conn . 2. Check the continuity between J43-3 <=> J432-3, J43-4 <=> J432-2 and J43-5 <=> J432-1. Is there the continuity between J43-3 <=> J423-3, J43-4 <=> J432-2 and J43-5 <=> J432-1? Go to step 10. Replace the Harness Assy Regi (J43- J431, J432). 10 PWBA CONN ANALYSIS 1. Disconnect the Harness Assy Conn (J23-J231) from the PWBA HKB26 MCU . 2. Check the continuity between P231-7 <=> P41-3, P231-6 <=> P41-5 and P231-10 <=> P43-4. Is there the continuity between J231-7 <=> J41-3, J231-6 <=> J41-5 and J231-10 <=> J43-4? Replace the PWBA HKB26 MCU . Replace the PWBA Conn . 11 DRUM SHUTTER of the CRU ANALYSIS Does the Drum Shutter open when you install the CRU? Go to step 12. Replace the CRU . 12 BTR ASSY ANALYSIS 1. Remove the CRU, so you can inspect the BTR Assy. 2. Check the rotation of the BTR Assy. Does the BTR Assy rotate smoothly? Go to step 13. Replace the BTR Assy . 13 BTR CHUTE ASSY ANALYSIS Inspect the BTR Chute Assy. Is the BTR Chute Assy clean and free of contamination? Clean or replace the BTR Assy or Chute Assy Trans . Go to step 14. 14 HEAT & PRESSURE ROLL of the FUSER ASSY ANALYSIS Check the rotation of the Heat and Pressure Rolls using MAIN MOTOR TEST. Are the Heat and Pressure Rolls rotating normally? Go to step 15. Replace the Fuser Assy . 15 DECURL ROLL of the FUSER ASSY ANALYSIS 1. Open the Cover Rear and cheat the Switch Assy I/ L Rear . 2. Execute a test print to check the Decurl Roll. Does the paper pass through the Decurl Roll without problems? Go to step 16 Replace the Fuser Assy 16 ACTUATOR EXIT of the Fuser Assy ANALYSIS Does the Exit Actuator move smoothly when a sheet of paper strikes it? Go to step 17. Replace the Fuser Assy . 17 SENSOR EXIT of the Fuser Assy ANALYSIS Check the Sensor Exit function using SENSOR/SWITCH CHECK. Does the Sensor Exit function correctly and increment the Sensor Check number on the screen each time you actuate it? Replace the PWBA HKB26 MCU . Replace the Fuser Assy .

← Xem tất cả mã lỗi OKI B6100

Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie