• Code: EC06 2F9A
• Description: Carriage lift motor error (support number : 4801)
• Causes: Overload on the lift motor.
• Remedy: 1 Check the items below. a) Cable connection of LIFT UNIT. b) Positioning CARRIAGE UNIT at the home position and butting against the lift unit, turn the gear of LIFT UNIT manually and check if the load is abnormally heavy. Appropriate Replace CARRIAGE UNIT. Inappropriate Replace LIFT UNIT. CARRIAGE UNIT is butting against the lift unit at the home position side.

• Code: EC06 2F9B
• Description: Carriage lift sensor error (support number : 4801)
• Causes: • Although the lift motor is rotating with generating larger than a constant torque, CARRIAGE LIFT SENSOR cannot detect ON/OFF.• CARRIAGE UNIT does not move to the home position during detecting home position.
• Remedy: 1 Check the items below. a) Cable connection of CARRIAGE LIFT SENSOR. b) Execute [DIAGNOSIS > I/O DISPLAY] and check the CARRIAGE LIFT SENSOR operation. Appropriate Replace CARRIAGE RELAY PCB UNIT. Inappropriate Replace LIFT UNIT.

• Code: EC06 2F9C
• Description: Carriage docking error (support number : 4801)
• Causes: • Although the lift motor is rotating, generated torque is smaller than a constant value. In addition, CARRIAGE LIFT SENSOR cannot detect ON/OFF. • CARRIAGE UNIT does not move to the home position during detecting home position.
• Remedy: 1 Check the items below. a) Check if CARRIAGE UNIT is positioned at the home position when the error occurs. b) If CARRIAGE UNIT is at the home position, check if the coupling part is damaged. Appropriate Go to EC05-2F92 error. Inappropriate a) Go to EC05-2F92 error. b) When the coupling at LIFT UNIT side is damaged Replace LIFT UNIT. When the coupling at CARRIAGE UNIT side is damaged Replace CARRIAGE UNIT.

• Code: EC07 2F19
• Description: Carriage acceleration sensor error (support number : 4801)
• Causes: Access to acceleration sensor is disabled.
• Remedy: 1 Perform [DIAGNOSIS > CR_SYSTEM_CHECK] to diagnose carriage system. Failure in ACC. SENSOR CHECK or CR VIBRATIONCHECK Replace CARRIAGE UNIT. Failure in LONG FFC CHECK or CRC value changes after turning the printer off and back on Replace FLEXIBLE CABLE UNIT.

• Code: EC07 4060
• Description: Carriage EEPROM error (support number : 6820) Memo : Remove the error in service mode when handling is completed.
• Causes: EEPROM defect in the carriage PCB is detected.
• Remedy: 1 Perform [DIAGNOSIS > CR_SYSTEM_CHECK] to diagnose carriage system. No problem Replace CARRIAGE UNIT. Failure in LONG FFC CHECK or CRC value changes after turning the printer off and back on Replace FLEXIBLE CABLE UNIT.

• Code: EC0F 2F93
• Description: Carriage jam error (support number : 1318) *Only this error code assigns jam code also.
• Causes: The detected value of acceleration sensor toward Y and Z direction exceeds the threshold.
• Remedy: 1 Open the access cover and check paper jam. When jam is found, remove the jam and check the operation again. Proper operation Complete. Check media specifications and use environment (temperature and humidity) of the customer, and give the customer appropriate instruction for jam prevention. Improper operation Replace CARRIAGE UNIT.

• Code: EC0F 2F96
• Description: Carriage motor error (support number : 4801)
• Causes: While carriage system is in error status, operation is indicated from firmware.
• Remedy: 1 Check the items below. a) Cable connection of the carriage motor. b) Looseness and abrasion of BELT, CARRIAGE. Appropriate Replace CARRIAGE UNIT. Inappropriate a) Connect the cable. b) Replace BELT, CARRIAGE.

• Code: EC11 2F2A
• Description: PAPER FEED home position error (support number : 4801)
• Causes: PAPER FEED home position adjustment is failed.
• Remedy: 1 Check the items below in PAPER FEED ENCODER UNIT. a) Installation of FILM, TIMING SLIT DISK, scratches, circumference shaving, and smear. b) Looseness and abrasion of BELT, PAPER TRANSPORT. c) Cable connection. d) Perform [DIAGNOSIS > I/O DISPLAY] and check the unit operation. Appropriate condition and proper operation Replace PAPER FEED ENCODER UNIT. Inappropriate condition or improper operation a) Perform cleaning or replace FILM, TIMING SLIT DISK. b) Rearrange or replace BELT, PAPER TRANSPORT. c) Cable connection. d) Replace PAPER FEED ENCODER UNIT.