• Code: 2E25
• Display: Cannot detect papr Remove paper and press Load/Eject. Cannot detect papr Remove paper and press OK.
• Description: Jam while picking up, ejecting or printing on paper (JAM2). After loading of roll paper or cut sheet was loaded successfully, Paper detection sensor/ Media sensor sensor detected no paper (JAM2).
• Remedy:

• Code: 2E27
• Display: Cannot load. Press Load/Eject and reload the paper. Paper jam. Press Load/Eject and reload the paper.
• Description: Feeding error (nip release required) LF out of synchronization (feed motor won't rotate) has been detected. Jam while picking up, ejecting or printing on paper (A sequence of removing jams with the pinch roller released is required)(JAM1) Virtually all recovery errors that could occur in connection with paper pickup are handled.
• Remedy: 1. Open and close the release lever to reload the paper. 2. Remove the paper once and then refeed it.

• Code: 2E30
• Display: The paper is too small.
• Description: Paper mismatch (size) With [Pause] selected for [Paper Mismatch Detection] in the menu setting, paper size for the paper loaded was smaller than the size specified by data.
• Remedy: Continued printing allowed. Check driver setting Replace with appropriate paper.

• Code: 2E31
• Display: Insufficient paper for job
• Description: All of the following conditions have been met at the start of external printing: -[ON] has been selected for [Remaining Roll Paper Detection]. -Among the paper size settings coded in the print data, the paper length exceeds the remaining length of roll paper. -Automatic roll feed to another roll paper slot which is not the current feeding path, out of the 2 slots the printer has, is not available.
• Remedy: Replace the roll paper.

• Code: 2E32
• Display: Insufficient paper for job
• Description: All of the following conditions have been met at the start of external printing: -[ON] has been selected for [Remaining Roll Paper Detection]. -Among the paper size settings coded in the print data, the paper length exceeds the remaining length of roll paper. -Automatic roll feed to another roll paper slot which is not the current feeding path, out of the 2 slots the printer has, is not available.
• Remedy: Replace the roll paper.

• Code: 2E33
• Display: Roll Paper (Paper type) (Paper size) Load Roll Paper Stop Printing. Roll 1(Upper) (Paper type) (Paper size) Press Load/Eject and load a roll.
• Description: Paper mismatch (roll paper) No roll paper has been fed when a job with a roll paper specification is received. Paper mismatch (roll paper) No roll paper has been fed when a job with a roll paper specification is received. When paper has not been loaded on either upper or lower slot, and the feeding slot is set to [Automatic] in the job setting, an error of upper roll occurs.
• Remedy: Load roll paper. 1. Select "load a roll" and follow instruction on the panel. 2. Select "stop printing," or stop printing by pressing stop button. 3. Release the release lever and load the paper.

• Code: 2E34
• Display: Roll 2 (Lower) (Paper type) (Paper size) Press Load/Eject and load a roll. Roll 2 (Lower) is selected. Press Load/Eject and load a roll.
• Description: Paper mismatch (roll paper) No roll paper has been fed when a job with a roll paper specification is received. When no paper has been loaded on either upper or lower slot, and the feeding slot is set to [Automatic] in the job setting, an error of upper roll (2E33) occurs. Paper mismatch (roll paper) No roll paper has been fed when a job with a roll paper specification is received. When no paper has been loaded on either upper or lower slot, and the feeding slot is set to [Automatic] in the job setting, an error of upper roll (2E33) occurs. * This is a message that appears when paper type/ size specification does not exist due to HPGL format etc.
• Remedy: Load roll paper.

• Code: 2E35
• Display: Roll printing is selected.
• Description: Paper mismatch (roll paper) No roll paper has been fed when performing internal printing.
• Remedy: Load roll paper.