Causes: An error was detected on the finisher side.
Remedy: 1. Check that the connector (CN1/P3/J3) of the Interface Harness is not disconnected. 2. Replace the Finisher Controller PCB. 3. Replace the Interface Harness.
Description: Front Alignment Plate HP Sensor error
Causes: The Front Alignment Motor did not move from the HP.
Remedy: 1. Check that the connector (P8-3/P8/J8) of the Front Alignment Plate HP Sensor (S4) is not disconnected. 2. Check that the connector (P6-12/P6-2/J6-2/P6/J6) of the Front Alignment Motor (M4) is not disconnected. 3. Replace the Front Alignment Plate HP Sensor (S4). 4. Replace the Front Alignment Motor (M4). 5. Check the conditions of the front alignment drive parts (belt and gear). 6. Replace the Finisher Controller PCB. 7. Replace the Harness Assembly.
Causes: The Front Alignment Motor did not return to the HP.
Remedy: 1. Check that the connector (P8-3/P8/J8) of the Front Alignment Plate HP Sensor (S4) is not disconnected. 2. Check that the connector (P6-12/P6-2/J6-2/P6/J6) of the Front Alignment Motor (M4) is not disconnected. 3. Replace the Front Alignment Plate HP Sensor (S4). 4. Replace the Front Alignment Motor (M4). 5. Check the conditions of the front alignment drive parts (belt and gear). 6. Replace the Finisher Controller PCB. 7. Replace the Harness Assembly.
Causes: The Staple Motor did not move from the HP.
Remedy: 1. Check that the connector (P9-1/P9/J9) of the Staple HP Sensor (S11) is not disconnected. 2. Check that the connector (P10-1/P10/J10) of the Staple Motor (M9) is not disconnected. 3. Replace the Stapler. 4. Replace the Finisher Controller PCB. 5. Replace the Harness Assembly.
Causes: The Staple Motor did not return to the HP.
Remedy: 1. Check that the connector (P9-1/P9/J9) of the Staple HP Sensor (S11) is not disconnected. 2. Check that the connector (P10-1/P10/J10) of the Staple Motor (M9) is not disconnected. 3. Replace the Stapler. 4. Replace the Finisher Controller PCB. 5. Replace the Harness Assembly.
Causes: The Rear Alignment Motor did not move from the HP.
Remedy: 1. Check that the connector (P7-5/P7/J7) of the Rear Alignment Plate HP Sensor (S5) is not disconnected. 2. Check that the connector (P5-13/P5-3/J5-3/P5/J5) of the Rear Alignment Motor (M5) is not disconnected. 3. Replace the Rear Alignment Plate HP Sensor (S5). 4. Replace the Rear Alignment Motor (M5). 5. Check the conditions of the rear alignment drive parts (belt and gear). 6. Replace the Finisher Controller PCB. 7. Replace the Harness Assembly.
Nhận ưu đãi sớm nhất khi chương trình diễn ra
Đăng ký nhận bản tin
Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này.
Chính sách cookie
Những cookie này là cần thiết để trang web hoạt động đúng cách.
Những cookie này giúp chúng tôi hiểu cách khách truy cập tương tác với trang web.
Những cookie này được sử dụng để cung cấp quảng cáo cá nhân hóa.