Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Canon iR8070 — Trang 6/14

Code: E204-0000

Description: There is an error in the detection of the image leading edge signal.
During forward movement in fixed reading mode or during a home position search, the image leading signal does not occur; or, in stream reading mode, the image leading edge signal does not arrive from the ADF controller PCB.
Remedy: Caution No code will be indicated. The keys will be locked. You can check the code in service mode (COPIER>DISPLAY>ERR). - Check if the scanner motor is connected properly, and replace the scanner motor if necessary. - Replace the scanner image leading edge sensor. - Replace the reader controller PCB.

Code: E211-0000

Description: The rise in temperature of the scanning lamp heater is faulty.
While the power is ON, the ambient temperature of the scanning lamp does not exceed 10 deg C 2 min after the florescent heater has gone ON; or, after the power is turned on, the reading of the ambient temperature of the scanning lamp is 0 deg C or lower.
Remedy: - Check if the connecter (J852, J853) of the light control PCB is mounted properly. - Replace the scanning lamp heater. - Replace the light control PCB. - Replace the reader controller PCB.

Code: E215-0000

Description: The rise in temperature of the scanning lamp heater is faulty.
While the scanning lamp is OFF, the reading of the ambient temperature is 170 deg C or higher.
Remedy: - Check if the connecter (J852, J853) of the light control PCB is mounted properly. - Replace the scanning lamp heater. - Replace the light control PCB. - Replace the reader controller PCB.

Code: E218-0000

Description: The scanning lamp is not mounted properly.
When the power is turned on, the absence of the scanning lamp is detected.
Remedy: - Check if the scannning lamp is mounted properly. - Check if the connecter (J1002, J1003) of the inverter PCB is mounted properly. - Check if the connector (J1720) of the relay PCB is mounted properly. - Replace the scanning lamp. - Replace the reader controller PCB.

Code: E219-0000

Description: The scanning lamp life
While the scanning lamp is ON, the reading of the ambient temperature is 170 deg C or higher.
Remedy: - Check if the connecter (J852, J853) of the light control PCB is mounted properly. - Replace the scanning lamp heater. - Replace the light control PCB. - Replace the reader controller PCB.

Code: E220-0000

Description: The lighting of the scanning lamp is faulty.
The scanning lamp does not reach a specific intensity within 10 sec after it is tuned on (if the room temperature is 10 deg C or lower, within 60 sec). Or, the ON detection signal (FL-DTCT) does not go OFF within 5 sec after the scanning lamp is turned off; during shading adjustment, the ON detection signal (FL-DTCT) does not go ON within 60 sec after the scanning lamp is turned on.
Remedy: - Check if the connecter (J852, J853) of the light control PCB is mounted properly. - Replace the scanning lamp heater. - Replace the light control PCB. - Replace the reader controller PCB.

Code: E222-0000

Description: The rise in temperature of the scanning lamp heater is faulty.
During the initial activation after power-on, the reading does not reach 70 deg C within 5 min after the heater is turned on. Or, during standby or reading operation, the reading does not reach 75 deg C within 3 min after the heater is tuned on.
Remedy: - Check if the connecter (J852, J853) of the light control PCB is mounted properly. - Replace the scanning lamp heater. - Replace the light control PCB. - Replace the reader controller PCB.

Code: E240-0000

Description: The communication between the MCON and DCON is faulty.
A communication fault exists between the CPUs of the main controller PCB and the DC controller PCB.
Remedy: - Check the wiring between the DC controller PCB and the main controller PCB. - Replace the DC controller PCB. - Replace the main controller PCB.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie