Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Epson Stylus Pro 10600 — Trang 7/9

Code: 00030018

Display: SERVICE CALL 00030018: INK SUPPLY DEFECTIVE (LC)
Description: Even if Isupply it ink the surface of a liquid sensor does not become full. It does not become defective (on I/C valve solenoid) or the surface of a liquid sensor defective
Remedy: • I/C valve solenoid exchange • C362DRV board exchange • Surface of a liquid sensor exchange

Code: 00030019

Display: SERVICE CALL 00030019: INK SUPPLY DEFECTIVE (LM)
Description: Even if Isupply it ink the surface of a liquid sensor does not become full. It does not become defective (on I/C valve solenoid) or the surface of a liquid sensor defective
Remedy: • I/C valve solenoid exchange • C362DRV board exchange • Surface of a liquid sensor exchange

Code: 0003001A

Display: SERVICE CALL 0003001A: INK SUPPLY DEFECTIVE (Y)
Description: Even if Isupply it ink the surface of a liquid sensor does not become full. It does not become defective (on I/C valve solenoid) or the surface of a liquid sensor defective
Remedy: • I/C valve solenoid exchange • C362DRV board exchange • Surface of a liquid sensor exchange

Code: 0003001B

Display: SERVICE CALL 0003001B:GAP ADJUSTMENT RANGE ERROR
Description: It is the adjustment value that is not able to adjust it to a hard target.
Remedy: • Gap (Bi-D, Uni-D) adjustment is done over again.

Code: 0003XXXX

Display: SERVICE CALL 0003XXXX: THE PROGRAM ERROR
Description: The error (the program error) that is not anticipating it.
Remedy: • Program retouch

Code: 0100

Display: MAINTENANCE CALL 0100
Description: The waste ink pads are almost full, causing a warning error. The printer can continue printing, but this messages overrides status messages such as Ready or Printing
Remedy: Replace the following parts and reset the counters as described below: Waste Ink Pads, Dot missing detector, Cleaning unit. After the above part are exchanged, "Waste ink Initialization" of maintenance mode 2 is run. NOTE: As for the above 3 parts the supply is possible as a regular part kit "Maintenance Kit Stylus Pro 10000/10000CF (No TBD)".

Code: 0101

Display: MAINTENANCE CALL 0101
Description: The CR motor reached the life.
Remedy: Replace the following parts: CR motor, Ink tube. After the above part are exchanged, "CR motor Initialization" of maintenance mode 2 is run.

Code: 0102

Display: MAINTENANCE CALL 0102
Description: There are dot missing on the print head. The next cause is conceivable. • The defectiveness of the print head. • Failure of the dot missing detector. • Offset value adjustment of the dot missing detector defective.
Remedy: Carry out the head nozzle checking in reference to 5.3.4.4.In the case that there are dot missing, the print head exchange.There are not dot missing, refer to 5.3.4.5 clause and carry out the offset adjustment. Exchanging the dot missing detector in the case that it does not release it even if it does the above correspondence,and carry out dot missing offset adjustment.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie