• Code: 09
• Image:
• Description: General Attention with Ability to Continue error
  The Attention light, Ready light, and Go light are blinking.
• Remedy: 1 Press (GO) to try to continue printing. 2 If the error persists, switch printer drivers and try again to print.

• Code: 10
• Image:
• Description: 68.x Permanent Storage error
  The Attention light is blinking. The nonvolatile memory (NVRAM) is temporarily full.
• Remedy: 1 Press (GO) to clear the message. Check the printer settings. 2 Remove the Jetdirect card, if it is installed (HP color LaserJet 2500 series printers only), and then perform a cold reset. 3 Perform a NVRAM init.

• Code: 11
• Image:
• Description: Accessory error secondary messages
  8x.yyyy EIO error The Attention light is blinking. A problem exists with the print server card. CAUTION: You must turn off the printer before inserting or removing the print server card to avoid damaging the print server card.
• Remedy: 1 Remove the print server card and reinstall it to make sure that it is correctly installed. 2 Make sure that you are using a supported print server card. See chapter 7 for ordering information. 3 To continue printing, remove the print server card from the EIO port and connect a parallel or USB cable. You must change the port or reinstall the software. 4 If the print server card still is not working, replace the print server.

• Code: 12
• Image:
• Description: Accessory error secondary messages
  53.x1.zz Printer (DIMM Slot 1) error The Go light is on. A problem exists with the DIMM in DIMM slot 1.
  CAUTION: You must turn off the printer before inserting or removing DIMMs to avoid damaging them.
• Remedy: 1 Remove the DIMM and reinstall it to make sure that it is correctly installed. 2 Make sure that you are using a supported DIMM. See chapter 7 for ordering information. 3 Move the DIMM to a different DIMM slot. If the DIMM works in a different slot, then DIMM slot 1 is malfunctioning. NOTE: Many of the first printers of this model were shipped with an 8 MB flash DIMM in DIMM slot 1. If the printer has an 8 MB flash DIMM in DIMM slot 1, then replace the DIMM. The 8 MB flash DIMM will not work in any DIMM slot other than DIMM slot 1. 4 To continue printing, remove the DIMM from DIMM slot 1.

• Code: 13
• Image:
• Description: Accessory error secondary messages
  53.x2.zz Printer (DIMM Slot 2) error
  The Ready light is on. A problem exists with the DIMM in DIMM slot 2.
  CAUTION: You must turn off the printer before inserting or removing DIMMs to avoid damaging them.
• Remedy: 1 Remove the DIMM and reinstall it to make sure that it is correctly installed. 2 Make sure that you are using a supported DIMM. See chapter 7 for ordering information. 3 Move the DIMM to a different DIMM slot. If the DIMM works in a different slot, then DIMM slot 2 is malfunctioning. 4 To continue printing, remove the DIMM from DIMM slot 2.

• Code: 14
• Image:
• Description: Accessory error secondary messages
  53.x3.zz Printer (DIMM Slot 3) error
  The Attention light is on. A problem exists with the DIMM in DIMM slot 3.
  CAUTION: You must turn off the printer before inserting or removing DIMMs to avoid damaging them.
• Remedy: 1 Remove the DIMM and reinstall it to make sure that it is correctly installed. 2 Make sure that you are using a supported DIMM. See chapter 7 for ordering information. 3 Move the DIMM to a different DIMM slot. If the DIMM works in a different slot, then DIMM slot 3 is malfunctioning. 4 To continue printing, remove the DIMM from DIMM slot 3.

• Code: 15
• Image:
• Description: Service error secondary messages
  51.x Bad beam detect error
  The Attention, Ready, and Go lights remain on.
• Remedy: 1 Press (GO). The page that contains the error will automatically be reprinted. 2 Turn the printer off and then back on. 3 Replace the laser/scanner.

• Code: 16
• Image:
• Description: Service error secondary messages
  52.x Scanner error
  The Ready light is on.
• Remedy: 1 Press (GO). The page that contains the error will automatically be reprinted. 2 Turn the printer off and then back on. 3 Turn the printer off, and then reseat the laser/scanner cable. 4 Replace the laser/scanner.