Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi HP Color LaserJet 8550 — Trang 4/10

Code: 22

Display: 22 PARALLEL I/O BUFFER OVERFLOW
Description: Indicates the parallel buffer has overflowed. This might happen if several complex jobs are sent simultaneously via the parallel port and are larger than the overflow will allow.
Remedy: No action is required. The current data in the print buffer will be lost.

Code: 30.00.01

Display: 30.00.01
Description: Hard disk internal self-test routine failure detection
Remedy: DISK DEVICE FAILURE

Code: 40

Display: 40.<n> HP EIO ERROR
Description: An EIO accessory connection has been abnormally broken while transferring data from the computer to the printer. <n> = EIO slot number 1 = Bottom EIO slot 2 = Top EIO slot
Remedy: 1 Press GO. 2 Print an EIO configuration page to verify that the EIO accessories are installed properly. 3 Check that all cables are connected to the EIO ports and that the EIO accessory is seated properly. 4 Turn the printer off and on to reset it. 5 If possible, print to another network printer to verify the network is working properly. All data in the print buffer will be lost.

Code: 40.00.01

Display: 40.00.01
Description: An EIO accessory is initializing.
Remedy: EIO <n> INITIALIZING

Code: 41.2

Display: 41.2 PRINTER ERROR
Description: Indicates that a beam detect laser scanner error has occurred on the previous page. The page will reprint and continue
Remedy: 1 Open and close the front door of the printer to remove any remaining pages from the printer. 2 Turn the printer off and on to reset the printer. 3 Reconnect connector J1001 on the laser driver PCA and connector J205 on the controller board. 4 Reconnect connector J2 on beam detect PCA, relay connector J40, and connector J211 on the controller board. 5 If the problem persists, replace the laser/ scanner unit. 6 If, after replacing the laser/scanner unit, the problem persists, replace the controller board.

Code: 41.3

Display: 41.3 UNEXPECTED PAPER SIZE LOAD TRAY 1
Description: Tray 1 is configured for a specific media size, but the printer detects a different size being fed from tray 1. For example, the printer was expecting a lettersized page but detected that an 11-by-17 inch-sized page was fed instead. <width> = Media width specified in the printer driver or application <length> = Media length specified in the printer driver or application
Remedy: 1 Verify the correct size media (width and length) are loaded in tray 1. 2 Verify the paper guides are set correctly. 3 Load the requested size media in tray 1. Or, press GO to print on the default size. 4 Verify that the media width sensor on the paper guides are working properly. 5 Reconnect connector J1701 on the tray 1 width detection PCA, relay connector J33, and connector J208 on the controller board. 6 Replace the tray 1 pick-up assembly.

Code: 41.5

Display: 41.5 UNEXPECTED PAPER TYPE LOAD TRAY <x>
Description: The printer was expecting one type of medium to be fed from an input tray and a different type was fed. For example, the printer was expecting transparencies and plain paper was fed. <x> = Input tray number (2, 3, or 4) <type> = Media type specified in the printer driver or application <size> = Media size specified in the printer driver or application Note: The size error in this message applies only to tray 1.
Remedy: 1 Open and close the front door to remove the page from the printer. 2 Verify that the correct media are loaded in the input tray and the printer control panel is configured correctly. 3 Clean the detection windows of OHT sensors 1 and 2. 4 Reconnect connectors J1801 and J1802 of OHT sensors 1 and 2, connector J214 on the controller board, and relay connector J17. 5 Replace OHT sensors 1 and 2. 6 Replace the controller board.

Code: 49

Display: 49.<xxxx> ERROR CYCLE POWER
Description: Indicates that a software or data communications error has occurred, or corrupt data was sent to the printer. This can be caused during times of high network traffic or by incomplete or out-of-bounds print data. This error can also occur because of defective EIO devices.
Remedy: 1 Verify that all cables are connected. 2 Turn the printer off and on to reset the printer. 3 Remove all EIO cards and reinstall them to ensure they are seated correctly. 4 If using a parallel connection, verify that the cable is IEEE-1284 compliant. 5 If the error occurs frequently, try adding more memory.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie