Code :

Code: 57.3
Display: 57.3 FAN FAILURE
Description: One of the cooling fans failed. 3 = Fan 3 (FM 3)
Remedy: Caution: Turn the printer off and do not operate the printer in this condition or it can be seriously damaged. 1 Turn the printer off and on to reset it. 2 Reconnect connectors J645 and J647 on the main relay PCA, J18 and J74 relay connectors, and connector J227 on the controller board. 3 Reconnect connector J641 on the main relay PCA, and connector J102 on the power supply. 4 Measure the voltage across J645-3 (FAN3ON) and J645-1 (GND) on the main relay PCA after the printer is turned on. If the voltage changes from 0 V to 24 V, replace fan 3. 5 Measure the voltage across connector J641-1 (+24 VB) and J641-4 (GND) on the main relay PCA after the printer is turned on. If the voltage is not 24 V, replace the main relay PCA. 6 Measure the voltage across connector J641-1 (-24 VB) and J641-4 (GND) on the main relay PCA after the printer is turned on. If the voltage is not 24 V, replace the main relay PCA. 7 Check the AC power supply. 8 If the problem is not rectified after the printer is turned off and on again, find the cause of activation of the overcurrent/overvoltage detection circuit in the power supply. Wait more than two minutes before turning the printer back on. 9 Replace the controller board.

Code: 58.1
Display: 58.1 ERROR CYCLE POWER
Description: Indicates that the paper diverter inside the right upper door is out of position, causing an error feeding media from tray 1.
Remedy: 1 Open the right upper door and check for a media jam or misfed media. 2 Turn the printer off and on to reset the printer.

Code: 59
Display: 59.<x> MOTOR ERROR CYCLE POWER
Description: Indicates that the main motor (M4) is not working properly.
<x> = Description: 0 = General error 1 = Startup error 2 = Rotation error
Remedy: 1 Turn the printer off and on to reset the printer. 2 Reconnect connector J219 and relay connector J1 on the controller board. 3 Replace the main motor (M4). 4 Reconnect connectors J641 to J643 and J647 on the main relay PCA, connectors J671 and J673 on the subrelay PCA, connector J102 on the power supply, and connector J227 on the controller board. 5 Check electrical continuity between connector J641-1 (+24 VB) and J642-3 (PMP) on the main relay PCA when the door switch (SW641) is turned on. If there is no electrical continuity, replace the main relay PCA. 6 Check electrical continuity between connector J671-2 (PMP) and J671-2 (PFUPR) on the subrelay PCA when the door switch (SW671) is turned on. If there is no electrical continuity, replace the subrelay PCA. 7 Measure the voltage across connector J647- B11 (+24 UH) and J647-4 (GND) on the main relay PCA after the printer is turned on. If the voltage is not 24 V, replace the main relay PCA. 8 Replace the controller board.

Code: 62
Display: 62.<x> SERVICE CYCLE POWER
Description: Indicates that a problem exists with the internal memory. <x> = Description: 0 = Internal ROM or RAM 1-8 = DIMM slots 1-8
Remedy: 1 Turn the printer off and on to reset the printer. 2 Perform DRAM DIMM test from the formatter diagnostics in the Service Menu. 3 If the problem persists, replace the bad DIMM.

Code: 63
Display: 63 SERVICE CYCLE POWER
Description: Indicates that the internal RAM memory test failed.
Remedy: 1 Turn the printer off and on to reset the printer. 2 Perform DRAM DIMM test from the formatter diagnostics in the Service Menu. 3 If the problem persists, replace the bad DIMM.

Code: 65
Display: 65 PRINTER ERROR CYCLE POWER
Description: Indicates a DRAM controller error.
Remedy: 1 Turn the printer off and on to reset the printer. 2 Perform DRAM DIMM test from the formatter diagnostics in the Service Menu. 3 If the problem persists, replace the bad DIMM.

Code: 66
Display: 66.<x>0.<yy> C-LINK COMM ERROR CHECK CABLES AND CYCLE POWER
Description: Indicates a communication error between the 2,000- sheet input unit or the multi-bin mailbox and the printer. <x> = Device number in the link <yy> = Error code from the optional device
Remedy: 1 Verify that the C-link and power cables are connected. 2 Turn the printer off and on to reset the printer.

‹ First < 5 6 7 8 9 10 >