Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi HP Color LaserJet CP5525 — Trang 7/16

Code: 50.9

Display: 50.WX.YZ Fuser error To continue
Description: The fuser has experienced an error. W = fuser error code, X = fuser mode, Y = previous printer sleep state, Z = next printer sleep state
High fuser temperature 2
Remedy: 1. Remove and then reseat the fuser. 2. Check the paper type setting using the product menus and in the printer driver. Making sure that they match and are correct for the type of media being used. 3. Replace the fuser. 4. If this product has been previously serviced, check the connector (J131) on the DC controller PCA.

Code: 50.A

Display: 50.WX.YZ Fuser error To continue
Description: The fuser has experienced an error. W = fuser error code, X = fuser mode, Y = previous printer sleep state, Z = next printer sleep state
Low fuser temperature 3
Remedy: 1. Remove and then reseat the fuser. Make sure there is no residual paper in the fuser. Make sure the device is not located in front of a vent or window where cool air may interfere with the ability of the fuser to heat up. 2. Check the product power source. Make sure the power source meets product requirements. Make sure this is the only device using the circuit. 3. Replace the fuser. 4. Check the connector (J704) between the fuser and the printer. If it is damaged, replace the fuser drive assembly or fuser. 5. If this product has been previously serviced, check the connector (J131) on the DC controller PCA and the connectors (J109 and J110) on the power line between the low-voltage power supply assembly and the fuser.

Code: 50.B

Display: 50.WX.YZ Fuser error To continue
Description: The fuser has experienced an error. W = fuser error code, X = fuser mode, Y = previous printer sleep state, Z = next printer sleep state
High fuser temperature 3
Remedy: 1. Remove and then reseat the fuser. 2. Check the paper type setting using the product menus and in the printer driver. Making sure that they match and are correct for the type of media being used. 3. Replace the fuser. 4. Check the connector (J704) between the fuser and the printer. If it is damaged, replace the fuser drive assembly or fuser. 5. If this product has been previously serviced, check the connector (J131) on the DC controller PCA.

Code: 51.00.20

Display: 51.00.YY Error
Description: Laser/scanner error
Black laser/scanner error
Remedy: Turn the product off, and then on. If the error persists, replace the laser/scanner assembly.

Code: 51.00.21

Display: 51.00.YY Error
Description: Laser/scanner error
Cyan laser/scanner error
Remedy: Turn the product off, and then on. If the error persists, replace the laser/scanner assembly.

Code: 51.00.22

Display: 51.00.YY Error
Description: Laser/scanner error
Magenta laser/scanner error
Remedy: Turn the product off, and then on. If the error persists, replace the laser/scanner assembly.

Code: 51.00.23

Display: 51.00.YY Error
Description: Laser/scanner error
Yellow laser/scanner error
Remedy: Turn the product off, and then on. If the error persists, replace the laser/scanner assembly.

Code: 52.00.00

Display: 52.XX.00 Error
Description: Laser/scanner errorer error
laser/scanner motor startup error
Remedy: Use the scanner motor (M10) drive test in the component test to test the motor. If the motor does not run, replace the laser/scanner assembly. NOTE: Listen for a high pitched whine from the motor. If the laser/scanner assembly has been removed or replaced, check the connectors (J831 and J832) on the laser-driver PCA and the connectors (J61 and J62) on the DC controller PCA.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie