Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi HP DesignJet 9000s — Trang 2/6

Code: 0100

Description: ASIC CONF (Carriage PCA)
The program load from the Flash ROM on the Main PCA to the ASIC on the Carriage PCA or sum-check was not performed correctly and an error occurred.
Remedy: • Reload the ASIC program from the IC Card. • Make sure that the Carriage Cable is correctly connected. • Replace the Carriage PCA. • Replace the Main PCA.

Code: 0200

Description: DRAM
The read/write of the image band memory on the Main PCA was diagnosed and an error was detected
Remedy: • Replace the Main PCA.

Code: 0400

Description: USB Register
The read/write of the USB controller on the Main PCA was diagnosed and an error was detected.
Remedy: • Replace the Main PCA.

Code: 0800

Description: Power Supply (+36V, +24V, +12V)
The power supplies of +36, +24 and +12 V were diagnosed and could not be detected.
Remedy: • Open the Electronics Cover and check LED 11 and LED 13. • If both LED 11 and LED 13 are OFF, then try the following: – Check the Interlock Switches to make sure they are installed/connected correctly. Make sure that the Rear Cover lips (that activate the Interlock Switches) are not bent and that the Rear Cover is closed correctly. – If the Interlock Switches are installed and connected correctly, then replace the Main PCA. • If both LED 11 and LED 13 are ON, then try the following: – Check whether the correct voltages are supplied from the power source (refer to the table below). If the correct voltages are not supplied, then replace the Power Supply Unit. – It is possible that this error occurred because of a faulty Main PCA. Replace the Main PCA. – Check whether the motors have been short-circuited by testing +24 V. If +24 V is not supplied then replace both Scan-Axis/Paper-Axis Motors. If error continues, replace the Main PCA.
+1.5 V TP70 +1.45 V to +1.55 V +3.3 V TP69 +3.20 V to +3.40 V +5 V REF TP36 +4.90 V to +5.10 V 5 V TP35 +4.75 V to +5.25 V +12 V TP50 +11.00 V to +13.00 V +24 V TP34 +23.00 V to +25.00 V +36 V TP93, TP33 +35.00 V to +37.00 V

Code: 1110

Description: GA_ATG Block Clear Error
The ATG band memory block erase does not end. This error is checked during Boot-Up sequence and printing.
Remedy: • Replace the Main PCA.

Code: 1111

Description: GA_ATG DMA Transfer Error
There is a problem in the data path. This error is checked during printing.
Remedy: • Make sure that the host PC and the Printer are connected correctly via a USB Cable. • Replace the Main PCA.

Code: 112x

Description: Vacuum Fan Error x = 0: The Vacuum Fan (Wiping Side) has failed. x = 1: The Vacuum Fan (Center of the Platen) has failed. x = 2: The Vacuum Fan (Capping Side) has failed.
Remedy: • Replace the failing Vacuum Fan. • If the error continues, replace the Main PCA.

Code: 1140

Description: Flash ROM Write Error
A time-out error occurs when the NVRAM contents are being saved in the flash memory in Maintenance Mode and erasing does not end.
Remedy: • Replace the Main PCA.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie