Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi HP DesignJet T7100 — Trang 2/18

Code: 06:03

Description: Hard Disk Drive
Causes: Main NVM communication failure
Remedy: • Turn the power off at the rear of the printer and disconnect the power cord. Reconnect the power cord and turn on the printer. • If the System Error continues, replace the Hard Disk Drive

Code: 06:10

Description: Hard Disk Drive
Causes: Main NVM communication failure
Remedy: • Turn the power off at the rear of the printer and disconnect the power cord. Reconnect the power cord and turn on the printer. • If the System Error continues, replace the Hard Disk Drive

Code: 08:11

Description: Front Panel
Causes: Front Panel communication failure
Remedy: • Turn the power off at the rear of the printer and disconnect the power cord. Reconnect the power cord and turn on the printer. • See What to do if the front panel is blank.

Code: 11:10

Description: Trailing Cable
Causes: Trailing Cable does not seem to be connected
Remedy: • Check that the Trailing Cable is not damaged. • Check that the Trailing Cable is correctly connected to the Carriage PCA, Interconnect PCA and Main PCA. • Replace the Ink Supply Tubes and Trailing Cable. NOTE: If the Ink Supply Tubes are to be replaced, the Ink Cartridges need to be checked beforehand to see if they are capable of purging the new tubes. If they are not, new Ink Cartridges must also be sent with the parts to be replaced.

Code: 17.0:11

Description: Other cables
Causes: PrintMech to Interconnect Power cable does not seem to be connected
Remedy: • Check that the PrintMech to Interconnect Power cable is not damaged. • Check that the PrintMech to Interconnect Power cable is correctly connected to the PrintMech PCA and the Interconnect PCA. • Replace the PrintMech to Interconnect Power cable (which is included in the Electronics Module Cable Kit).

Code: 17.1:11

Description: Other cables
Causes: PrintMech to Interconnect Data 1 cable does not seem to be connected
Remedy: • Check that the PrintMech to Interconnect Data 1 cable is not damaged. • Check that the PrintMech to Interconnect Data 1 cable is correctly connected to the PrintMech PCA and the Interconnect PCA. • Replace the PrintMech to Interconnect Data 1 cable (which is included in the Electronics Module Cable Kit).

Code: 17.2:11

Description: Other cables
Causes: PrintMech to Interconnect Data 2 cable does not seem to be connected
Remedy: • Check that the PrintMech to Interconnect Data 2 cable is not damaged. • Check that the PrintMech to Interconnect Data 2 cable is correctly connected to the PrintMech PCA and the Interconnect PCA. • Replace the PrintMech to Interconnect Data cable 2 (which is included in the Electronics Module Cable Kit).

Code: 17.3:11

Description: Other cables
Causes: Main PCA to PrintMech Black 1 cable does not seem to be connected
Remedy: • Check that the Main PCA to PrintMech Black 1 cable is not damaged. • Check that the Main PCA to PrintMech Black 1 cable is correctly connected to the Main PCA and the PrintMech PCA. • Replace the Main PCA to PrintMech Black 1 cable (which is included in the Electronics Module Cable Kit).
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie