Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Konica-Minolta bizhub 36 — Trang 6/8

Code: 3000

Description: Transport motor’s failure to turn
The motor lock signal remains HIGH for a predetermined continuous period of time while the motor remains stationary
Remedy: 1 Check the connector between M1-PRCB CN3 for proper connection and correct as necessary. 2 Check M1 for proper drive coupling and correct as necessary. 3 M1 operation check. 4 Change M1. 5 Change PRCB

Code: 3FFB

Description: Finisher ROM error (FS-529)
Data of flash ROM of the finishing options is determined to be faulty when the power switch is turned ON.
Remedy: 1 Disconnect and then connect the power cord. Turn OFF the main power switch, wait for 10 sec. or more, and turn ON the power switch. 2 Rewrite firmware. 3 Change FSCB

Code: 6751

Description: Gain adjustment error
Reading the white pixel output of each color from the data provided by the shading plate, the machine makes the gain adjustment for each color so that the maximum value of each color becomes within the specified range. However, after the machine attempts the adjustment three times in total (including two retries), the value is out of the specified range.
Remedy: 1 Reboot the main unit. 2 Clean the original glass. 3 Check the connector CN102, CN103 on MFPB for proper connection and correct as necessary. 4 Change scanner unit. 5 Change MFPB.

Code: 6790

Description: Offset adjustment error
Reading the black pixel output of each color from the data provided by the shading plate, the machine makes the offset adjustment for each color so that the average value of each color becomes within the specified range. However, after the machine attempts the offset adjustment three times in total (including two retries), the value is out of the specified range.
Remedy: 1 Reboot the main unit. 2 Clean the original glass. 3 Check the connector CN102, CN103 on MFPB for proper connection and correct as necessary. 4 Change scanner unit. 5 Change MFPB.

Code: 6791

Description: Register setting error
After the default values of AFE gain and offset are set, the machine reads the gain and offset values again. Inconsistency between the values that are set and read is found.
Remedy: 1 Reboot the main unit. 2 Check the connector CN102, CN103 on MFPB for proper connection and correct as necessary. 3 Change MFPB.

Code: 6792

Description: White reference plate search error
During an initialization, the black edge and the white edge read by the shading plate cannot be detected.
Remedy: 1 Reboot the main unit. 2 Clean the original glass. 3 Check the connector CN102, CN103 on MFPB for proper connection and correct as necessary. 4 Change scanner unit. 5 Change MFPB.

Code: 6793

Description: Scanner communication error
An undefined communication error occurs between the controller and the scanner.
Remedy: 1 Reboot the main unit. 2 Clean the original glass. 3 Check the connector CN102, CN103 on MFPB for proper connection and correct as necessary. 4 Change scanner unit. 5 Change MFPB.

Code: 9401

Description: Lamp illumination check error
In the lamp stabilization check process during the lamp warm-up, light quantity does not become steady within a given period of time.
Remedy: 1 Reboot the main unit. 2 Clean the original glass. 3 Check the connector CN102, CN103 on MFPB for proper connection and correct as necessary. 4 Change scanner unit. 5 Change MFPB.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie