• Code: C1105
• Description: Bundle eject motor drive malfunction (When FS-534 or FS-534SD is installed) • The gripper home position sensor (PS18) is not turned ON (blocked) even after the set period of time has elapsed after the gripper position detection sensor (PS19) is turned OFF (unblocked). • The gripper position detection sensor (PS19) is not turned OFF (unblocked) even after the set period of time has elapsed after it is turned ON (blocked). • The gripper position detection sensor (PS19) is not turned ON (blocked) even after the set period of time has elapsed after the gripper home position sensor (PS18) is turned OFF (unblocked). • The gripper home position sensor (PS18) is not turned OFF (unblocked) even after the set period of time has elapsed after the bundle eject motor (M10) is energized. • The gripper home position sensor (PS18) and the gripper position detection sensor (PS19) is turned ON (blocked) at the same time.
• Causes: • Bundle eject motor (M10) • Gripper home position sensor (PS18) • Gripper position detection sensor (PS19) • FS control board (FSCB)
• Remedy: 1. Check the motor and sensor connectors for proper connection, and correct as necessary. 2. Check the connector of M10 for proper drive coupling, and correct as necessary. 3. PS18 I/O check, sensor check • Control signal: FSCB J13-13 (ON) • Location of electrical component: FS-534 7-C 4. PS19 I/O check, sensor check • Control signal: FSCB J12-3 (ON) • Location of electrical component: FS-534 7-C 5. M10 operation check • Control signal: FSCB J13-1 to 2 • Location of electrical component: FS-534 8-C to D 6. Replace M10. 7. Replace FSCB.

• Code: C1106
• Description: Stapler movement motor malfunction (When FS-533, FS-534 or FS-534SD is installed) <When FS-533 is installed> • The stapler home sensor (PS110) is not turned OFF (unblocked) after the laps of given time after it started operating from the home position. • The stapler home sensor (PS110) is not turned ON (blocked) after the laps of give time after the stapler movement motor (M107) turned ON when it returned to the home position. <When FS-534 or FS-534SD is installed> • The stapler home position sensor (Rear) (PS23) is not turned ON (blocked) or OFF (unblocked) even after the set period of time has elapsed after the side stapler movement motor (M13) turned ON. • The stapler does not reach the specified position within the set period of time.
• Causes: <When FS-533 is installed> • Stapler movement motor (M107) • Stapler home sensor (PS110) • Stapler relay board (STREYB) • FS control board (FSCB) <When FS-534 or FS-534SD is installed> • Side stapler movement motor (M13) • Stapler home position sensor (Rear) (PS23) • FS control board (FSCB)
• Remedy: (a) When FS-533 is installed 1. Check the connector between M107-STREYB CN123 for proper connection, and correct as necessary. 2. Check the connector of M107 for proper drive coupling, and correct as necessary. 3. Check the connector between PS110-FSCB CN110 for proper connection, and correct as necessary. 4. PS110 I/O check, sensor check • Control signal: FSCB CN110 • Location of electrical component: FS-533 8-D to E 5. M107 operation check • Control signal: STREYB CN123-5 to 8 • Location of electrical component: FS-533 5-L 6. Replace M107. 7. Replace STREYB. 8. FSCB CP107 conduction check 9. Replace FSCB. NOTICE • Link to the wiring diagram (N.2.5 FS-533) (b) When FS-534 or FS-534SD is installed 1. Check the connector between M13-relay CN3-FSCB J11 for proper connection, and correct as necessary. 2. Check the connector of M13 for proper drive coupling and correct as necessary. 3. Check the connector between PS23-relay CN3-FSCB J11 for proper connection, and correct as necessary. 4. PS23 I/O check, sensor check • Control signal: FSCB J11<B>-3 (ON) • Location of electrical component: FS-534 4-C 5. M13 operation check • Control signal: FSCB J11<A>-1 to 4 • Location of electrical component: FS-534 4-C to D 6. Replace M13. 7. Replace FSCB.

• Code: C1109
• Description: Stapler motor drive malfunction (When FS-533, FS-534 or FS-534SD is installed) <When FS-533 is installed> • The stapler home sensor (PS110) is not turned ON (blocked) even after the set period of time has elapsed after the stapler motor turned ON. <When FS-534 or FS-534SD is installed> • The stapler home position sensor (Rear) (PS23) is not turned ON (blocked) or OFF (unblocked) even after the set period of time has elapsed after the stapler motor (M14) turned ON. • The stapler position sensor (Center) (PS24) is turned ON (blocked), when the stapler motor (M14) is running.
• Causes: <When FS-533 is installed> • Stapler home sensor (PS110) • Stapler unit • Stapler relay board (STREYB) • FS control board (FSCB) <When FS-534 or FS-534SD is installed> • Stapler home position sensor (Rear) (PS23) • Stapler unit • Stapler position sensor (Center) (PS24) • FS control board (FSCB)
• Remedy: (a) When FS-533 is installed 1. Check the connector between the stapler unit-STREYB CN122 and CN123 for proper connection and correct as necessary. 2. Check the connector of the stapler unit for proper drive coupling and correct as necessary. 3. Check the connector between PS110-FSCB CN110 for proper connection and correct as necessary. 4. PS110 I/O check, sensor check • Control signal: FSCB CN110 • Location of electrical component: FS-533 8-D to E 5. Replace the stapler unit. 6. Replace STREYB. 7. Replace FSCB. NOTICE • Link to the wiring diagram (N.2.5 FS-533) (b) When FS-534 or FS-534SD is installed 1. Check the connector between the stapler unit-relay CN4-FSCB J11 for proper connection and correct as necessary. 2. Check the connector of the stapler unit for proper drive coupling and correct as necessary. 3. Check the connector between PS23-relay CN3-FSCB J11 for proper connection, and correct as necessary. 4. Check the connector between PS24-relay CN3-FSCB J11 for proper connection and correct as necessary. 5. PS23 I/O check, sensor check • Control signal: FSCB J11<B>-3 (ON) • Location of electrical component: FS-534 4-C 6. PS24 I/O check, sensor check • Control signal: FSCB J11<B>-6 (ON) • Location of electrical component: FS-534 4 to 5-C 7. Replace the stapler unit. 8. Replace FSCB.

• Code: C1112
• Description: Stapler motor malfunction (When FS-534SD is installed) • The stapler home sensor is not turned ON even after the set period of time has elapsed while the stapler motor is energized. • The stapler home sensor is not turned OFF even after the set period of time has elapsed after the stapler home sensor is turned ON.
• Causes: • Staple unit • SD drive board (SDDB) • FS control board (FSCB)
• Remedy: 1. Check the connector between the staple unit-SDDB J4 for proper connection and correct as necessary. 2. Check the connector of the staple unit for proper drive coupling and correct as necessary. 3. Replace the staple unit. 4. Replace SDDB. 5. Replace FSCB.

• Code: C1113
• Description: Center-staple lead edge stopper motor malfunction (When FS-534SD is installed) The stopper home sensor (PS6) is not turned ON (blocked) or OFF (unblocked) even after the set period of time has elapsed after the stopper drive motor (M4) is turned ON.
• Causes: • Stopper drive motor (M4) • Stopper home sensor (PS6) • SD drive board (SDDB) • FS control board (FSCB)
• Remedy: 1. Check the connector between M4-SDDB J10 for proper connection and correct as necessary. 2. Check the connector of M4 for proper drive coupling and correct as necessary. 3. Check the connector between PS6-SDDB J10 for proper connection and correct as necessary. 4. PS6 I/O check, sensor check • Control signal: SDDB J10-5 (ON) • Location of electrical component: SD-511 2-G 5. M4 operation check • Control signal: SDDB J10-6 to 9 • Location of electrical component: SD-511 1 to 2-F to G 6. Replace M4. 7. Replace SDDB. 8. Replace FSCB.

• Code: C1114
• Description: Center-staple front adjust drive motor malfunction (When FS-534SD is installed) The alignment home sensor (PS4) is not turned ON (blocked) or OFF (unblocked) even after the set period of time has elapsed after the alignment motor (M3) is turned ON.
• Causes: • Alignment motor (M3) • Alignment home sensor (PS4) • SD drive board (SDDB) • FS control board (FSCB)
• Remedy: 1. Check the connector between M3-relay CN10-SDDB J7 for proper connection and correct as necessary. 2. Check the connector of M3 for proper drive coupling and correct as necessary. 3. Check the connector between PS4-relay CN10-SDDB J7 for proper connection and correct as necessary. 4. PS4 I/O check, sensor check • Control signal: SDDB J7-6 (ON) • Location of electrical component: SD-511 6-F 5. M3 operation check • Control signal: SDDB J7-7 to 10 • Location of electrical component: SD-511 5-F to G 6. Replace M3. 7. Replace SDDB. 8. Replace FSCB.

• Code: C1115
• Description: Center-staple knife drive motor malfunction (When FS-534SD is installed) The center fold knife home sensor (PS8) is not turned ON (blocked) or OFF (unblocked) even after the set period of time has elapsed after the center fold knife motor (M9) is turned ON.
• Causes: • Center fold knife motor (M9) • Center fold knife home sensor (PS8) • SD drive board (SDDB) • FS control board (FSCB)
• Remedy: 1. Check the connector between M9-SDDB J11 for proper connection and correct as necessary. 2. Check the connector of M9 for proper drive coupling and correct as necessary. 3. Check the connector between PS8-relay CN10-SDDB J7 for proper connection and correct as necessary. 4. PS8 I/O check, sensor check • Control signal: SDDB J7-3 (ON) • Location of electrical component: SD-511 6-G 5. M9 operation check • Control signal: SDDB J11-11 to 20 • Location of electrical component: SD-511 1 to 2-B 6. Replace M9. 7. Replace SDDB. 8. Replace FSCB.

• Code: C1132
• Description: Punch drive motor malfunction (When FS-533+PK-519, FS-534+PK-520 or FS-534SD+PK-520 is installed) <When FS-533+PK-519 is installed> • The puncher drive cam sensor (PS203) or puncher home sensor (PS204) is not turned ON (blocked) or OFF (unblocked) even after the set period of time has elapsed while the punch motor (M201) is energized. • The punch motor sensor (PS202) is not turned ON when the punch motor (M201) driven. • The holes with other marketing area is set in [Service Mode] -> [Finisher] -> [Punch Option Setting]. <When FS-534+PK-520 or FS-534SD+PK-520 is installed> • The punch home sensor (PS1) is not turned ON (blocked) or OFF (unblocked) even after the set period of time has elapsed while the punch drive motor (M1) is energized. • Thick paper is loaded and a punch operation is performed with [Plain Paper] left set for the paper type.
• Causes: <When FS-533+PK-519 is installed> • Punch motor (M201) • Punch motor sensor (PS202) • Puncher drive cam sensor (PS203) • Puncher home sensor (PS204) • PK control board (PKCB) • FS control board (FSCB) <When FS-534+PK-520 or FS-534SD+PK-520 is installed> • Punch drive motor (M1) • Punch home sensor (PS1) • FS control board (FSCB)
• Remedy: 1. Check the number of the holes in [Service Mode] -> [Finisher] -> [Punch Option Setting]. 2. Check the connector between M201-PKCB CN203 for proper connection and correct as necessary. 3. Check the connector of M201 for proper drive coupling and correct as necessary. 4. Check the connector between PS202-PKCB CN204 for proper connection and correct as necessary. 5. Check the connector between PS203-PKCB CN204 for proper connection and correct as necessary. 6. Check the connector between PS204-PKCB CN204 for proper connection and correct as necessary. 7. PS202 I/O check, sensor check • Control signal: PKCB CN204 • Location of electrical component: FS-533 (PK-519) 5-C 8. PS203 I/O check, sensor check • Control signal: PKCB CN204 • Location of electrical component: FS-533 (PK-519) 6-C 9. PS204 I/O check, sensor check • Control signal: PKCB CN204 • Location of electrical component: FS-533 (PK-519) 6-C 10. M201 operation check • Control signal: PKCB CN203-1 to 2 • Location of electrical component: FS-533 (PK-519) 4-C 11. Replace M201. 12. PKCB F201 conduction check 13. Replace PKCB. 14. Replace FSCB. NOTICE • Link to the wiring diagram (N.2.5 FS-533) (b) When FS-534+PK-520 or FS-534SD+PK-520 is installed 1. Check that the correct paper type is set. To print on thick paper, change the paper type to [Thick]. 2. If the trouble occurs even when [Paper Type] is set to the correct paper type, select [Service Mode] -> [Security Settings] -> [Engine FW DipSW] and flip SW No. 17 to the ON. NOTE • Changing the setting of Engine FW DipSW results in a longer perforating time and greater punch perforating noise regardless of the paper type. 3. Check the connector between M1-relay CN351-FSCB J7 for proper connection and correct as necessary. 4. Check the connector of M1 for proper drive coupling and correct as necessary. 5. Check the connector between PS1-FSCB J7 for proper connection and correct as necessary. • Control signal: FSCB J7-5 (ON) • Location of electrical component: FS-534 (PK-520) 7-K 6. PS1 I/O check, sensor check • Control signal: FSCB J7-7 to 8 • Location of electrical component: FS-534 (PK-520) 7-K 7. M1 operation check 8. Replace M1. 9. Replace FSCB.