• Code: C1140
• Description: Alignment plate motor/Rr malfunction (When FS-533, FS-534 or FS-534SD is installed) <When FS-533 is installed> • The alignment plate home sensor/R (PS109) is not turned OFF (unblocked) after the set period of time has elapsed after the plate drive starts from the home position. • The alignment plate home sensor/R (PS109) is not turned ON (blocked) after the set period of time has elapsed while the alignment motor/R (M106) is energized when the plate returns to the home position. <When FS-534 or FS-534SD is installed> • The alignment plate/R home sensor (PS13) is not turned ON (blocked) or OFF (unblocked) even after the set period of time has elapsed while the alignment motor/Rear (M8) is energized.
• Causes: <When FS-533 is installed> • Alignment motor/R (M106) • Alignment plate home sensor/R (PS109) • FS control board (FSCB) <When FS-534 or FS-534SD is installed> • Alignment motor/Rear (M8) • Alignment plate/R home sensor (PS13) • FS control board (FSCB)
• Remedy: (a) When FS-533 is installed 1. Check the connector between M106-FSCB CN102 for proper connection and correct as necessary. 2. Check the connector of M106 for proper drive coupling and correct as necessary. 3. Check the connector between PS109-FSCB CN102 for proper connection and correct as necessary. 4. PS109 I/O check, sensor check • Control signal: FSCB CN102 • Location of electrical component: FS-533 7-J 5. M106 operation check • Control signal: FSCB CN102 • Location of electrical component: FS-533 8-J 6. Replace M106 7. FSCB CP105 conduction check 8. Replace FSCB NOTICE • Link to the wiring diagram (N.2.5 FS-533) (b) When FS-534 or FS-534SD is installed 1. Check the connector between M8-FSCB J12 for proper connection and correct as necessary. 2. Check the connector of M8 for proper drive coupling and correct as necessary. 3. Check the connector between PS13-FSCB J9 for proper connection and correct as necessary. 4. PS13 I/O check, sensor check • Control signal: FSCB J9<B>-9 (ON) • Location of electrical component: FS-534 9-C 5. M8 operation check • Control signal: FSCB J12-13 to 16 • Location of electrical component: FS-534 5 to 6-C to D 6. Replace M8. 7. Replace FSCB.

• Code: C1141
• Description: Paddle motor drive malfunction (When FS-534 or FS-534SD is installed) The upper paddle home position detection sensor (PS14) is not turned ON (blocked) or OFF (unblocked) even after the set period of time has elapsed while the FNS paddle motor (M5) is turning.
• Causes: • FNS paddle motor (M5) • Upper paddle home position detection sensor (PS14) • FS control board (FSCB)
• Remedy: 1. Check the connector between M5-FSCB J4 for proper connection and correct as necessary. 2. Check the connector of M5 for proper drive coupling and correct as necessary. 3. Check the connector between PS14-FSCB J4 for proper connection and correct as necessary. 4. PS14 I/O check, sensor check • Control signal: FSCB J4<B>-7 (ON) • Location of electrical component: FS-534 13-C 5. M5 operation check • Control signal: FSCB J4<A>-5 to 8 • Location of electrical component: FS-534 12-C to D 6. Replace M5. 7. Replace FSCB.

• Code: C1144
• Description: Pre-eject drive motor malfunction (When FS-534 or FS-534SD is installed) • The pre-eject home sensor (PS21) is not turned ON (blocked) or OFF (unblocked) even after the set period of time has elapsed after the pre-eject drive motor (M9) is turned ON. • The pre-eject away sensor (PS22) is not turned ON (blocked) or OFF (unblocked) even after the set period of time has elapsed after the pre-eject drive motor (M9) is turned ON.
• Causes: • Pre-eject drive motor (M9) • Pre-eject home sensor (PS21) • Pre-eject away sensor (PS22) • FS control board (FSCB)
• Remedy: 1. Check the connector between M9-relay CN7<A>-FSCB J13 for proper connection, and correct as necessary. 2. Check the connector of M9 for proper drive coupling and correct as necessary. 3. Check the connector between PS21-relay CN8-relay CN7<B>-FSCB J12 for proper connection, and correct as necessary. 4. Check the connector between PS22-relay CN8-relay CN7<B>-FSCB J12 for proper connection, and correct as necessary. 5. PS21 I/O check, sensor check • Control signal: FSCB J12-6 (ON) • Location of electrical component: FS-534 6-C 6. PS22 I/O check, sensor check • Control signal: FSCB J12-9 (ON) • Location of electrical component: FS-534 6-C 7. M9 operation check • Control signal: FSCB J13-3 to 4 • Location of electrical component: FS-534 8-C to D 8. Replace M9. 9. Replace FSCB.

• Code: C1145
• Description: Trailing edge stopper motor malfunction (When FS-534 or FS-534SD is installed) The trailing edge stopper home position detection sensor (PS20) is not turned ON (blocked) or OFF (unblocked) even after the set period of time has elapsed after the trailing edge stopper motor (M6) is turned ON.
• Causes: • Trailing edge stopper motor (M6) • Trailing edge stopper home position detection sensor (PS20) • FS control board (FSCB)
• Remedy: 1. Check the connector between M6-FSCB J5 for proper connection and correct as necessary. 2. Check the connector of M6 for proper drive coupling and correct as necessary. 3. Check the connector between PS20-relay CN22-FSCB J5 for proper connection and correct as necessary. 4. PS20 I/O check, sensor check • Control signal: FSCB J5-9 (ON) • Location of electrical component: FS-534 9-K 5. M6 operation check • Control signal: FSCB J5-13 to 16 • Location of electrical component: FS-534 9-K 6. Replace M6. 7. Replace FSCB.

• Code: C1156
• Description: SD paddle motor malfunction (When FS-534SD is installed) The paddle home sensor (PS5) is not turned ON (blocked) or OFF (unblocked) even after the set period of time has elapsed while the SD paddle motor (M7) is energized.
• Causes: • SD paddle motor (M7) • Paddle home sensor (PS5) • SD drive board (SDDB) • FS control board (FSCB)
• Remedy: 1. Check the connector between M7-SDDB J8 for proper connection and correct as necessary. 2. Check the connector of M7 for proper drive coupling and correct as necessary. 3. Check the connector between PS5-SDDB J8 for proper connection and correct as necessary. 4. PS5 I/O check, sensor check • Control signal: SDDB J8-3 (ON) • Location of electrical component: SD-511 3 to 4-G 5. M7 operation check • Control signal: SDDB J8-4 to 7 • Location of electrical component: SD-511 3-F to G 6. Replace M7. 7. Replace SDDB. 8. Replace FSCB.

• Code: C1182
• Description: Shift motor drive malfunction (When JS-506 is installed) • The tray shift home sensor (PS1) is not turned ON (blocked) after the set period of time has elapsed after the tray shift motor (M1) is turned ON (start of moving to the home position.) • The tray shift home sensor (PS1) is not turned OFF (unblocked) after the set period of time has elapsed after the tray shift motor (M1) is turned ON (start of moving to the shift position.)
• Causes: • Tray shift motor (M1) • Tray shift home sensor (PS1) • JS control board (JSCB)
• Remedy: 1. Check the connector between M1-JSCB CN208 for proper connection and correct as necessary. 2. Check the connector of M1 for proper drive coupling and correct as necessary. 3. Check the connector between PS1-JSCB CN208 for proper connection and correct as necessary. 4. PS1 I/O check, sensor check • Control signal: JSCB CN208-5 (ON) • Location of electrical component: JS-506 5-C 5. M1 operation check • Control signal: JSCB CN208-1 (DRV) • Location of electrical component: JS-506 4 to 5-C 6. Replace M1. 7. JSCB ICP3 conduction check 8. Replace JSCB.

• Code: C1184
• Description: Paper discharge control motor malfunction (When FS-534 or FS-534SD is installed) The paper delivery control sensor (PS28) is not turned ON (blocked) or OFF (unblocked) even after the set period of time has elapsed while the paper receiving control motor (M12) is energized.
• Causes: • Paper receiving control motor (M12) • Paper delivery control sensor (PS28) • FS control board (FSCB)
• Remedy: 1. Check the connector between M12-relay CN1-FRCB J14 for proper connection and correct as necessary. 2. Check the connector of M12 for proper drive coupling and correct as necessary. 3. Check the connector between PS28-relay CN1-FRCB J14 for proper connection and correct as necessary. 4. PS28 I/O check, sensor check • Control signal: FSCB J14<B>-3 (ON) • Location of electrical component: FS-534 2 to 3-C 5. M12 operation check • Control signal: FSCB J14<A>-9 to 12 • Location of electrical component: FS-534 2-C to D 6. Replace M12. 7. Replace FSCB.

• Code: C1195
• Description: Paper discharge control motor malfunction (When FS-534SD is installed) The curl cover detection sensor (PS2) is not turned ON (blocked) or OFF (unblocked) even after the set period of time has elapsed after the paper discharge control motor (M2) is turned ON.
• Causes: • Paper discharge control motor (M2) • Curl cover detection sensor (PS2) • SD drive board (SDDB) • FS control board (FSCB)
• Remedy: 1. Check the connector between M2-relay CN3-relay CN2-SDDB J5 for proper connection and correct as necessary. 2. Check the connector of M2 for proper drive coupling and correct as necessary. 3. Check the connector between PS2-relay CN3-relay CN2-SDDB J5 for proper connection and correct as necessary. 4. PS2 I/O check, sensor check • Control signal: SDDB J5-3 (ON) • Location of electrical component: SD-511 3-B 5. M2 operation check • Control signal: SDDB J5-4 to 7 • Location of electrical component: SD-511 3-B 6. Replace M2. 7. Replace SDDB. 8. Replace FSCB.