Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Konica-Minolta bizhub 423

Code: C0001

Description: LCT communication error
• Due to malfunctioning of the software or other causes, the watchdog timer triggers a reset when time is up.
Remedy: 1 Turn OFF the main power switch, wait for 10 sec. or more, and turn ON the main power switch. 2 PCCB51 replacement

Code: C0202

Description: Tray 1 feeder up/down abnormality
• The paper feed tray 1 upper limit sensor (PS12) is not blocked even after the lapse of a given period of time after the lifting motion has been started.
Remedy: 1 Check the connector between M11-PRCB CN12 for proper connection and correct as necessary. 2 Check the connector of M11 for proper drive coupling and correct as necessary. 3 Check the connector between PS12-relay CN1-PRCB CN13 for proper connection and correct as necessary. 4 PS12 I/O check. 5 M11 operation check. 6 Change M11. 7 Change PRCB.

Code: C0204

Description: Tray 2 feeder up/down abnormality
• The paper feed tray 2 upper limit sensor (PS22) is not blocked even after the lapse of a given period of time after the lifting motion has been started.
Remedy: 1 Check the connector between M21-PRCB CN11 for proper connection and correct as necessary. 2 Check the connector of M21 for proper drive coupling and correct as necessary. 3 Check the connector between PS22-relay CN6-PRCB CN14 for proper connection and correct as necessary. 4 PS22 I/O check. 5 M21 operation check. 6 Change M21. 7 Change PRCB.

Code: C0206

Description: Tray 3 lift-up failure
• The tray 3 upper limit sensor (PS33) is not blocked even after the set period of time has elapsed after the paper lift-up operation for the drawer began.
Remedy: 1 Check the connector between M33- PCCB31 CN4 for proper connection and correct as necessary. 2 Check the connector between M43- PCCB31 CN8 for proper connection and correct as necessary. 3 Check the connector between PS33-relay CN18-PCCB31 CN6 for proper connection and correct as necessary. 4 Check the connector between PS43-relay CN18-PCCB31 CN10 for proper connection and correct as necessary. 5 Check the connector of each motor for proper drive coupling, and correct as necessary. 6 PS33 I/O check, sensor check. 7 PS43 I/O check, sensor check. 8 M33 operation check. 9 M43 operation check. 10 Change PRCB31. 11 Change PRCB.

Code: C0208

Description: Tray 4 lift-up failure
• The tray 4 upper limit sensor (PS43) is not blocked even after the set period of time has elapsed after the paper lift-up operation for the drawer began.
Remedy: 1 Check the connector between M33- PCCB31 CN4 for proper connection and correct as necessary. 2 Check the connector between M43- PCCB31 CN8 for proper connection and correct as necessary. 3 Check the connector between PS33-relay CN18-PCCB31 CN6 for proper connection and correct as necessary. 4 Check the connector between PS43-relay CN18-PCCB31 CN10 for proper connection and correct as necessary. 5 Check the connector of each motor for proper drive coupling, and correct as necessary. 6 PS33 I/O check, sensor check. 7 PS43 I/O check, sensor check. 8 M33 operation check. 9 M43 operation check. 10 Change PRCB31. 11 Change PRCB.

Code: C0209

Description: LCT elevator motor failure
• The elevator motor sensor (PS5A) cannot detect both edges of H/L even after the set period of time has elapsed while the elevator motor (M55) is turning backward/forward (raise/lower).
Remedy: 1 Check the connector between M55- PCREYB CN2 for proper connection and correct as necessary. 2 Check the connector between PS5APCREYB CN2 for proper connection and correct as necessary. 3 Check the connector of M55 for proper drive coupling, and correct as necessary. 4 PS5A I/O check, sensor check. 5 M55 operation check. 6 Change PCREYB. 7 Change PCCB.

Code: C0210

Description: LCT lift failure
• The lift-up upper limit sensor (PS54) is not blocked even after the set period of time has elapsed after the paper lift-up operation began. • The lift-up upper limit sensor (PS54) is not blocked even after the set pulse is detected by the elevator motor sensor (PS5A) after the paper lift-up operation began. • The lift-down lower limit sensor (PS5D) is not unblocked even after the set pulse is detected by the elevator motor sensor (PS5A) after the paper lift-up operation began. • The lift-up upper limit sensor (PS54) is not blocked even after the set period of time has elapsed after the paper lift-up operating. • The lift-down lower limit sensor (PS5D) is not blocked even after the set period of time has elapsed after the paper lift-down operation began. • The lift-down lower limit sensor (PS5D) is not blocked even after the set pulse is detected by the elevator motor sensor (PS5A) after the paper lift-down operation began. • The lift-up upper limit sensor (PS54) is not unblocked even after the set pulse is detected by the elevator motor sensor (PS5A) after the paper lift-down operation began. • The lift-down over run sensor (PS57) is blocked while the paper lift-down operating.
Remedy: 1 Check the connector between PS54-relay CN20-PCCB51 PJ5 for proper connection and correct as necessary. 2 Check the connector between PS5DPCREYB CN2 for proper connection and correct as necessary. 3 Check the connector between PS5APCREYB CN2 for proper connection and correct as necessary. 4 Check the connector between PS57- PCREYB CN2 for proper connection and correct as necessary. 5 PS54 I/O check, sensor check. 6 PS5D I/O check, sensor check. 7 PS5A I/O check, sensor check. 8 PS57 I/O check, sensor check. 9 Change PCCB51

Code: C0211

Description: Manual feed up/down abnormality
• Paper does not unblock the manual lift-up position sensor (PS83) even after the transport motor (M1) rotates for a given period of time after the position is switched from stand by position at lift-up plate to the feed position. • The manual lift-up position sensor (PS83) is not blocked even after the transport motor (M1) rotates for a given period of time after the position is switched from stand by position at lift-up plate to the feed position.
Remedy: 1 Check the connector between M1-PRCB CN3 for proper connection and correct as necessary. 2 Check the connector of M1 for proper drive coupling and correct as necessary. 3 Check the connector between PS83-PRCB CN9 for proper connection and correct as necessary. 4 Check the connector between SD81-relay CN99-relay CN15-PRCB CN9 for proper connection and correct as necessary. 5 PS83 I/O check, sensor check. 6 SD81 operation check. 7 M1 operation check. 8 Change M1. 9 Change PRCB.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie