Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Konica-Minolta bizhub 554e — Trang 19/24

Code: CC164

Description: ROM contents error (MSC). • The wrong model of firmware is detected in the MFP board when the main power switch is turned ON. • The machine type information (Machine, Type) registered to the machine differs from the actual machine type.
Causes: • Printer control board (PRCB) • MFP board (MFPB)
Remedy: 1 Check the ROM version. 2 Check the machine type information registered and reenter as necessary. For details the machine information, see “J.2.4 Entering the machine type information”. 3 Rewrite the firmware. 4 Replace the corresponding board. 5 If the above actions do not solve the problem, contact KM.

Code: CC165

Description: ROM contents error (DF). When the power is turned ON, DF control board or firmware error is detected.
Causes: DF control board (DFCB)
Remedy: 1 Turn OFF the main power switch, disconnect and then connect the power cord. Wait for 10 sec. or more after connect the power cord, and turn ON the main power switch. 2 Rewrite the firmware. 3 Replace DFCB

Code: CC170 ... CC186

Description: Dynamic link error during starting (AP0) Dynamic link error during starting (AP1) Dynamic link error during starting (AP2) Dynamic link error during starting (AP3) Dynamic link error during starting (AP4) Dynamic link error during starting (LDR) Dynamic link error during starting (IBR) Dynamic link error during starting (IID) Dynamic link error during starting (IPF) Dynamic link error during starting (IMY) Dynamic link error during starting (SPF) Dynamic link error during starting (OAP)
Causes: A dynamic link error occurs in the program on the MFP board due to an insufficient memory space available, a ROM fault, or other reason when the main power switch is turned ON. MFP board (MFPB)
Remedy: 1 If the malfunction code “CC172” has occurred, access [Service Mode] -> [System 2] -> [Image Controller Setting] and check to see if “Controller 1,” “Controller 2,” “Controller 3,” or “Others” is set for [Image Controller Setting]. If any of these is set, select “Controller 0.” 2 If the malfunction code "C-C180" has occurred, check to install the appropriate loadable device driver for an authentication unit which is installed to the MFP. When the appropriate loadable device driver is not installed, reinstall the appropriate loadable device driver. 3 Replace MFPB 4 If the above actions do not solve the problem, contact KM.

Code: CC190

Description: Outline font load error. An error occurred while loading the outline font.
Causes: • MFP board (MFPB) • Hard disk
Remedy: 1 Check the connector between hard disk-MFPB PJ11 for proper connection and correct as necessary. 2 Format hard disk. 3 Replace the hard disk. 4 Replace MFPB

Code: CC191

Description: Setting parameter load error (LDR). Upon startup, the processing of the loadable device driver setting data file failed. • RAM disk file creation failed. • Reading from the flash ROM failed. • An error occurred in API of the authentication module.
Causes: MFP board (MFPB)
Remedy: 1 Turn OFF the main power switch, wait for 10 sec. or more, and turn ON the main power switch. 2 Reinstall the loadable device driver. 3 Rewrite the firmware. 4 Replace MFPB

Code: CC211

Description: Authentication device general error. When using the authentication device, authentication data is not to meet the specifications.
Causes: • MFP board (MFPB) • Authentication device
Remedy: 1 Check the USB cable for proper connection and correct as necessary. 2 Turn OFF the main power switch, wait for 10 sec. or more, and turn ON the main power switch.

Code: CC212

Description: User validation error. • An error occurred while validating the user authentication information. • The loadable device driver is not successfully installed.
Causes: • MFP board (MFPB) • Authentication device
Remedy: 1 When this trouble code is generated after installing the loadable device driver, check to see if there is any file other than loadable device driver in USB memory used. If there is any file, reinstall the loadable device driver. 2 Check the USB cable for proper connection and correct as necessary. 3 Turn OFF the main power switch, wait for 10 sec. or more, and turn ON the main power switch. 4 Re-register the user authentication information. 5 Replace authentication device.

Code: CC213

Description: • User registration error • Card information setting error Detection timing • IC card advanced settings data is not correct when starting-up the authentication device. • Authentication information data is not correct when starting-up the authentication device. • IC card advanced settings data is not correct when setting the IC card advanced settings. • Authentication information data is not correct when setting the IC card advanced settings. • IC card advanced settings data is not correct when registering the authentication information. • Authentication information data is not correct when registering the authentication information. • IC card advanced settings data is not correct when editing the authentication information. • Authentication information data is not correct when editing the authentication information
Causes: • MFP board (MFPB) • Authentication device
Remedy: 1 Check the USB cable for proper connection and correct as necessary. 2 Turn OFF the main power switch, wait for 10 sec. or more, and turn ON the main power switch. 3 Reset the authentication settings. (card type, IC card advanced settings, and etc.) 4 Re-register the user authentication information.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie